Hyundai R 160 LC-3 Скачать руководство пользователя страница 215 | Manualshive

Страница: 215 / 459

background image

5- 32

This lamp is turned on when the filter in the air cleaner is clogged.
Check the filter and wash or replace it when the lamp is ON.

AIR CLEANER WARNING LAMP

10)

ڸ
ڹ

This lamp is turned ON when the temperature of coolant is over
the normal temperature(110

Ş

C) and lose the cooling function.

Check the coolant when the lamp is ON.

OVERHEAT WARNING LAMP

11)

ڸ

ڹ

This lamp is turned ON when the coolant temperature is below
30

Ş

C.

The automatic warming up is canceled when the engine coolant
temperature is above 30

Ş

C, or when 10 minutes have passed

since starting.

WARMING UP LAMP

12)

ڸ

ڹ

The lamp of selected mode is turned ON by pressing the right
switch( , ), when selecting the mode to use.

ş

H : This is used for heavy-duty work.

ş

S : This is used for ordinary work.

ş

L : This is used for light-duty work.

ş

F : This is used for light-duty work, especially for finishing work.

At each pressing of the switch, a short term beep sounds.

MODE SELECTION SWITCH

13)

POWER MODE

H

F

L

S

ڸ

ڹ

This switch is used to select the auto-deceleration function.
If the auto deceleration function is activated the engine speed is
lowered when temporary stop or stand-by for dump is required.
At each pressing of the switch, a short term beep sounds.

AUTO DECELERATION SWITCH

14)

AUTO
DECEL

H

ڸ
ڹ

ں

«
...
213
214
215
216
217
...
»

Содержание R 160 LC-3












































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R 160 LC-3

Бренд: Yanmar Страницы: 240

Бренд: Takeuchi Страницы: 18

Бренд: Garbin Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды