HP A7L26UT#ABA Скачать руководство пользователя страница 183 | Manualshive

Страница: 183 / 200

background image

Table D-17

Solving Front Panel Component Problems (continued)

A USB device, headphone, or microphone is not recognized by the computer.

Cause

Solution

The device is not working.

1.

Replace the device.

2.

Restart the computer.

USB ports on the computer are disabled in Computer Setup.

Run the Computer Setup utility and ensure that

Device

available

is selected for appropriate USB ports under

Security

>

USB Security

.

Solving Internet Access Problems

If you encounter Internet access problems, consult your Internet Service Provider (ISP) or refer to the
common causes and solutions listed in the following table.

Table D-18

Solving Internet Access Problems

Unable to connect to the Internet.

Cause

Solution

Internet Service Provider (ISP) account is not set up
properly.

Verify Internet settings or contact your ISP for assistance.

Modem is not set up properly.

Reconnect the modem. Verify the connections are correct
using the quick setup documentation.

Web browser is not set up properly.

Verify that the Web browser is installed and set up to work
with your ISP.

Cable/DSL modem is not plugged in.

Plug in cable/DSL modem. You should see a “power” LED
light on the front of the cable/DSL modem.

Cable/DSL service is not available or has been interrupted
due to bad weather.

Try connecting to the Internet at a later time or contact your
ISP. (If the cable/DSL service is connected, the “cable” LED
light on the front of the cable/DSL modem will be on.)

The CAT5 UTP cable is disconnected.

Connect the CAT5 UTP cable between the cable modem
and the computers’s RJ-45 connector. (If the connection is
good, the “PC” LED light on the front of the cable/DSL
modem will be on.)

IP address is not configured properly.

Contact your ISP for the correct IP address.

Cookies are corrupted. (A “cookie” is a small piece of
information that a Web server can store temporarily with the
Web browser. This is useful for having the browser
remember some specific information that the Web server can
later retrieve.)

1.

Select

Start

>

Control Panel

.

2.

Click

Network and Internet

.

3.

Click

Internet Options

.

4.

In the

Browsing history

section on the

General

tab,

click the

Delete

button.

5.

Select the

Cookies

check box and click the

Delete

button.

Solving Internet Access Problems 173

«
...
181
182
183
184
185
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

Бренд: IBM Страницы: 158

Бренд: Yawarra Страницы: 4

Бренд: Harbor Freight Tools Страницы: 4

Бренд: IBM Страницы: 500

TIGW1U - Carrier Grade Server

Бренд: Intel Страницы: 11

TRS-80 Model 100

Бренд: Radio Shack Страницы: 210

Бренд: Everex Страницы: 47

Бренд: Gateway Страницы: 346

Бренд: Acer Страницы: 136

Бренд: Acer Страницы: 88

BX-951-DC series

Бренд: Contec Страницы: 111

Бренд: Casio Страницы: 81

Бренд: Asus Страницы: 80

Бренд: Asus Страницы: 35

Бренд: Asus Страницы: 56

Бренд: Asus Страницы: 35

Бренд: Asus Страницы: 69

Бренд: Asus Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды