HP A7L26UT#ABA Скачать руководство пользователя страница 27

Страница: 27 / 200

Recovering the Configuration Settings

This method of recovery requires that you first perform the

Save to Removable Media

command

with the Computer Setup (F10) Utility before

Restore

is needed.

NOTE:

It is recommended that you save any modified computer configuration settings to a USB

flash media device and save the device for possible future use.

To restore the configuration, insert the USB flash media device with the saved configuration and
perform the

Restore from Removable Media

command with the Computer Setup (F10) Utility.

Recovering the Configuration Settings

Содержание A7L26UT#ABA









































































































































































































Результаты поиска

Содержание A7L26UT#ABA

Отзывы:

Похожие инструкции для A7L26UT#ABA

Бренды по названию

Популярные бренды

HP A7L26UT#ABA, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание A7L26UT#ABA

Отзывы:

Похожие инструкции для A7L26UT#ABA

Бренды по названию

Популярные бренды