HP A7L26UT#ABA Скачать руководство пользователя страница 151 | Manualshive

Страница: 151 / 200

background image

●

Refer to the comprehensive online technical support at

http://www.hp.com/support

.

●

Refer to

Helpful Hints on page 141

in this guide.

To assist you in resolving problems online, HP Instant Support Professional Edition provides you with
self-solve diagnostics. If you need to contact HP support, use HP Instant Support Professional
Edition's online chat feature. Access HP Instant Support Professional Edition at:

http://www.hp.com/

go/ispe

.

Access the Business Support Center (BSC) at

http://www.hp.com/go/bizsupport

for the latest online

support information, software and drivers, proactive notification, and worldwide community of peers
and HP experts.

If it becomes necessary to call for technical assistance, be prepared to do the following to ensure that
your service call is handled properly:

●

Be in front of your computer when you call.

●

Write down the computer serial number, product ID number, and monitor serial number before
calling.

●

Spend time troubleshooting the problem with the service technician.

●

Remove any hardware that was recently added to your system.

●

Remove any software that was recently installed.

●

Restore the system from the Recovery Disc Set that you created or restore the system to its
original factory condition in HP Backup and Recovery Manager.

CAUTION:

Restoring the system will erase all data on the hard drive. Be sure to back up all data

files before running the restore process.

NOTE:

For sales information and warranty upgrades (Care Packs), call your local authorized

service provider or dealer.

Helpful Hints

If you encounter problems with the computer, monitor, or software, see the following list of general
suggestions before taking further action:

●

Check that the computer and monitor are plugged into a working electrical outlet.

●

Check that the voltage select switch (some models) is set to the appropriate voltage for your
region (115V or 230V).

●

Check that the computer is turned on and the green power light is on.

●

Check that the monitor is turned on and the green monitor light is on.

●

Check the Power LED on the front of the computer to see if it is flashing red. The flashing lights
are error codes that will help you diagnose the problem. Refer to Appendix A,

POST Error

Messages on page 127

for more information.

●

Turn up the brightness and contrast controls of the monitor if the monitor is dim.

●

Press and hold any key. If the system beeps, then the keyboard should be operating correctly.

●

Check all cable connections for loose connections or incorrect connections.

Helpful Hints 141

«
...
149
150
151
152
153
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

PowerBox 310 Series

Бренд: Spectra Страницы: 116

Network Adapter EmETX-i602

Бренд: Socket Страницы: 11

Бренд: IBM Страницы: 27

Бренд: LDI Spaces Страницы: 5

Бренд: XtendLan Страницы: 65

Бренд: IPSO Страницы: 41

Бренд: Speaka Professional Страницы: 4

Бренд: Star Lake Страницы: 46

Бренд: Partner Страницы: 52

Бренд: AVERATEC Страницы: 64

Link Lectern Media Manager Series

Бренд: Spectrum Страницы: 17

Бренд: Radio Shack Страницы: 163

Бренд: IBM Страницы: 88

Бренд: Quanmax Страницы: 36

Бренд: Tangent Страницы: 18

686536U - IntelliStation Z - Pro 6865

Бренд: IBM Страницы: 160

Бренд: Barco Страницы: 4

Бренд: Gateway Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды