HP A7L26UT#ABA Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 200

background image

Table D-4

Solving Hard Drive Problems (continued)

Drive not found (identified).

Cause

Solution

The system may not have automatically recognized a newly
installed device.

See reconfiguration directions in the

Solving Hardware

Installation Problems on page 163

section. If the system still

does not recognize the new device, check to see if the
device is listed within Computer Setup. If it is listed, the
probable cause is a driver problem. If it is not listed, the
probable cause is a hardware problem.

If this is a newly installed drive, run the Computer Setup
utility and try adding a POST delay under

Advanced

>

Power-On

.

The device is attached to a SATA port that has been hidden
in Computer Setup.

Run the Computer Setup utility and ensure

Device Available

is selected for the device's SATA port in

Security

>

Device

Security

.

Drive responds slowly immediately after power-up.

Run Computer Setup and increase the POST Delay in

Advanced

>

Power-On Options

.

Nonsystem disk/NTLDR missing message.

Cause

Solution

The system is trying to start from a diskette that is not
bootable.

Remove the diskette from the diskette drive.

The system is trying to start from the hard drive but the hard
drive may have been damaged.

1.

Insert a bootable diskette into the diskette drive and
restart the computer.

2.

Check the hard drive format using fdisk: If NTFS
formatting, use a third party reader to evaluate the
drive. If FAT32 formatting, the hard drive cannot be
accessed.

System files missing or not properly installed.

1.

Insert a bootable diskette into the diskette drive and
restart the computer.

2.

Check the hard drive format using Fdisk: If NFTFS
formatting, use a third party reader to evaluate the
drive. If FAT32 formatting, the hard drive cannot be
accessed.

3.

Install system files for the appropriate operating system.

Hard drive boot has been disabled in Computer Setup.

Run the Computer Setup utility and enable the hard drive
entry in the

Storage

>

Boot Order

list.

Bootable hard drive is not attached as first in a multi-hard
drive configuration.

If attempting to boot from a hard drive, ensure it is attached
to the system board dark blue SATA connector.

Bootable hard drive's controller is not listed first in the Boot
Order.

Run the Computer Setup utility and select

Storage

>

Boot

Order

and ensure the bootable hard drive's controller is

listed immediately under the

Hard Drive

entry.

150 Appendix D Troubleshooting Without Diagnostics

«
...
158
159
160
161
162
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

Staff Workstation 795

Бренд: 3M Страницы: 6

Dynapro ET 3200 Series

Бренд: 3M Страницы: 21

DECstation 316+

Бренд: DEC Страницы: 94

Бренд: Aaeon Страницы: 90

Бренд: Compaq Страницы: 69

eon 5000 Series

Бренд: Neoware Страницы: 40

Бренд: VS Страницы: 20

DESK-V000V Series

Бренд: Vivo Страницы: 12

Бренд: Shuttle Страницы: 34

Edition X103 SFF

Бренд: Fujitsu Siemens Computers Страницы: 49

Бренд: Fujitsu Siemens Computers Страницы: 64

SCENIC Edition X100

Бренд: Fujitsu Siemens Computers Страницы: 65

Бренд: Shuttle Страницы: 1

Бренд: Xerox Страницы: 73

Horizon Workstation 2 Person

Бренд: Jason.L Страницы: 3

Horizon Workstation 2 Person Run

Бренд: Jason.L Страницы: 4

Бренд: Quanmax Страницы: 26

Бренд: Tangent Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды