HP A7L26UT#ABA Скачать руководство пользователя страница 169 | Manualshive

Страница: 169 / 200

background image

Table D-7

Solving Audio Problems (continued)

Sound does not come out of the speaker or headphones.

Cause

Solution

Some applications can select which audio output device is
used.

Make sure the application has selected the correct audio
device.

The operating system controls may be set to use a different
audio device as the default output device than what is
expected.

Set the operating system to use the correct audio device.

Sound from headphones is not clear or muffled.

Cause

Solution

Headphones are plugged into the rear audio output
connector. The rear audio output connector is for powered
audio devices and is not designed for headphone use.

Plug the headphones into the headphone connector on the
front of the computer.

Computer appears to be locked up while recording audio.

Cause

Solution

The hard disk may be full.

Before recording, make sure there is enough free space on
the hard disk. You can also try recording the audio file in a
compressed format.

Line-in jack is not functioning properly.

Cause

Solution

Jack has been reconfigured in the audio driver or application
software.

In the audio driver or application software, reconfigure the
jack or set the jack to its default value.

There is no sound or sound volume is too low.

Cause

Solution

The application is set to use a different audio device than
speakers.

Some graphics cards support audio over the DisplayPort
connection, so multiple audio devices may be listed in
Device Manager. Make sure the correct device is being
used.

Some applications can select which audio output device is
used.

Make sure the application has selected the correct audio
device.

The operating system controls may be set to use a different
audio device as the default output device than what is
expected.

Set the operating system to use the correct audio device.

Solving Audio Problems 159

«
...
167
168
169
170
171
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

Бренд: Ohio Scientific Страницы: 43

Бренд: Canon Страницы: 160

CYRAQ PPC Series

Бренд: CyberResearch Страницы: 103

Бренд: Everex Страницы: 47

Ultra Box nForce SLI Socket Barebone 939

Бренд: Ultra Products Страницы: 1

Firestorm 1Z490X

Бренд: ACE COMPUTERS Страницы: 42

Бренд: Gateway Страницы: 140

Бренд: VIA Mainboard Страницы: 68

ProDesk 400 G7 SFF

Бренд: HP Страницы: 10

Бренд: HP Страницы: 2

ProDesk 400 G2.5

Бренд: HP Страницы: 9

ProDesk 400 G3 MT

Бренд: HP Страницы: 9

Pro 3015 - Microtower PC

Бренд: HP Страницы: 3

Бренд: HP Страницы: 6

Бренд: HP Страницы: 3

Pro 3080 - Microtower PC

Бренд: HP Страницы: 7

Pro 3005 - Microtower PC

Бренд: HP Страницы: 6

ProDesk 400 G6 MT

Бренд: HP Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды