HP A7L26UT#ABA Скачать руководство пользователя страница 135 | Manualshive

Страница: 135 / 200

background image

B

Power Cord Set Requirements

The power supplies on some computers have external power switches. The voltage select switch
feature on the computer permits it to operate from any line voltage between 100-120 or 220-240 volts
AC. Power supplies on those computers that do not have external power switches are equipped with
internal switches that sense the incoming voltage and automatically switch to the proper voltage.

The power cord set received with the computer meets the requirements for use in the country where
you purchased the equipment.

Power cord sets for use in other countries must meet the requirements of the country where you use
the computer.

General Requirements

The requirements listed below are applicable to all countries:

1.

The power cord must be approved by an acceptable accredited agency responsible for
evaluation in the country where the power cord set will be installed.

2.

The power cord set must have a minimum current capacity of 10A (7A Japan only) and a
nominal voltage rating of 125 or 250 volts AC, as required by each country’s power system.

3.

The diameter of the wire must be a minimum of 0.75 mm

2

or 18AWG, and the length of the cord

must be between 1.8 m (6 feet) and 3.6 m (12 feet).

The power cord should be routed so that it is not likely to be walked on or pinched by items placed
upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point
where the cord exits from the product.

WARNING!

Do not operate this product with a damaged power cord set. If the power cord set is

damaged in any manner, replace it immediately.

Japanese Power Cord Requirements

For use in Japan, use only the power cord received with this product.

CAUTION:

Do not use the power cord received with this product on any other products.

General Requirements 125

«
...
133
134
135
136
137
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

Бренд: Acer Страницы: 106

Бренд: Acer Страницы: 83

Бренд: Acer Страницы: 81

Бренд: Acer Страницы: 89

T230H - Bmidh Wide Touch Screen Display

Бренд: Acer Страницы: 12

Бренд: Acer Страницы: 100

Бренд: Kaypro Страницы: 157

Бренд: Acer Страницы: 51

Бренд: 7starlake Страницы: 32

Бренд: Advantech Страницы: 44

Бренд: Asus Страницы: 2

VAIO PCV-RX470DS

Бренд: Sony Страницы: 101

Бренд: Toshiba Страницы: 4

Бренд: Toshiba Страницы: 8

A20-S259 - Satellite - Pentium 4 2.66 GHz

Бренд: Toshiba Страницы: 12

Бренд: Toshiba Страницы: 50

Бренд: Toshiba Страницы: 56

dynaEdge DE-10 Series

Бренд: Toshiba Страницы: 137

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды