HP A7L26UT#ABA Скачать руководство пользователя страница 142

Страница: 142 / 200

Table C-1

Numeric Codes and Text Messages (continued)

Control panel message

Description

Recommended action

1720-SMART Hard Drive Detects Imminent
Failure

Hard drive is about to fail. (Some hard
drives have a hard drive firmware patch that
will fix an erroneous error message.)

Determine if hard drive is giving correct
error message. Enter Computer Setup
and run the Drive Protection System
test under

Storage

DPS Self-test

Apply hard drive firmware patch
if applicable. (Available at

http://www.hp.com/support

Back up contents and replace hard
drive.

1796-SATA Cabling Error

One or more SATA devices are improperly
attached. For optimal performance, the
SATA 0 and SATA 1 connectors must be
used before SATA 2 and SATA 3.

Ensure SATA connectors are used in
ascending order. For one device, use SATA
0. For two devices, use SATA 0 and SATA
1. For three devices, use SATA 0, SATA 1,
and SATA 2.

1797-SATA Drivelock is not supported in
RAID mode.

Drivelock is enabled on one or more SATA
hard drives, and they cannot be accessed
while the system is configured for RAID
mode.

Either remove the Drivelocked SATA device
or disable the Drivelock feature. To disable
the Drivelock feature, enter Computer
Setup, change

Storage

Options

SATA Emulation

IDE

, and

select

File

Save Changes and Exit

Reenter Computer Setup and select

Security

Drivelock Security

. For each

listed Drivelock-capable SATA device,
ensure Drivelock is

Disabled

. Lastly,

change

Storage

Storage Options

SATA Emulation

back to

RAID

and select

File

Save Changes and Exit

1801-Microcode Patch Error

Processor is not supported by ROM BIOS.

Upgrade BIOS to proper version.

Change the processor.

2200-PMM Allocation Error during MEBx
Download

Memory error during POST execution of the
Management Engine (ME) BIOS Extensions
option ROM.

Reboot the computer.

Unplug the power cord, re-seat the
memory modules, and reboot the
computer.

If the memory configuration was
recently changed, unplug the
computer, restore the original memory
configuration, and reboot the
computer.

If the error persists, replace the system
board.

132 Appendix C POST Error Messages

Содержание A7L26UT#ABA









































































































































































































Результаты поиска

Содержание A7L26UT#ABA

Отзывы:

Похожие инструкции для A7L26UT#ABA

Бренды по названию

Популярные бренды

HP A7L26UT#ABA, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание A7L26UT#ABA

Отзывы:

Похожие инструкции для A7L26UT#ABA

Бренды по названию

Популярные бренды