HP A7L26UT#ABA Скачать руководство пользователя страница 170 | Manualshive

Страница: 170 / 200

background image

Solving Printer Problems

If you encounter printer problems, see the documentation that came with the printer and to the
common causes and solutions listed in the following table.

Table D-8

Solving Printer Problems

Printer will not print.

Cause

Solution

Printer is not turned on and online.

Turn the printer on and make sure it is online.

The correct printer drivers for the application are not
installed.

1.

Install the correct printer driver for the application.

2.

Try printing using the MS-DOS command:

DIR C:\ > [printer port]

where

[printer port]

is the address of the printer being

used. If the printer works, reload the printer driver.

If you are on a network, you may not have made the
connection to the printer.

Make the proper network connections to the printer.

Printer may have failed.

Run printer self-test.

Printer will not turn on.

Cause

Solution

The cables may not be connected properly.

Reconnect all cables and check the power cord and
electrical outlet.

Printer prints garbled information.

Cause

Solution

The correct printer driver for the application is not installed.

Install the correct printer driver for the application.

The cables may not be connected properly.

Reconnect all cables.

Printer memory may be overloaded.

Reset the printer by turning it off for one minute, then turn it
back on.

Printer is offline.

Cause

Solution

The printer may be out of paper.

Check the paper tray and refill it if it is empty. Select online.

160 Appendix D Troubleshooting Without Diagnostics

«
...
168
169
170
171
172
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

Бренд: Barco Страницы: 202

Бренд: IBM Страницы: 132

Бренд: IBM Страницы: 140

IntelliStation Z Pro 6223

Бренд: IBM Страницы: 134

IntelliStation Z Pro 6221

Бренд: IBM Страницы: 168

IntelliStation E Pro

Бренд: IBM Страницы: 80

IntelliStation A Pro 6224

Бренд: IBM Страницы: 132

Бренд: IBM Страницы: 206

IntelliStation M Pro

Бренд: IBM Страницы: 190

Бренд: IBM Страницы: 450

Бренд: IBM Страницы: 112

Бренд: IBM Страницы: 124

Бренд: IBM Страницы: 152

Бренд: IBM Страницы: 206

Бренд: IBM Страницы: 64

6275 - PC 300 GL

Бренд: IBM Страницы: 88

Бренд: DFI Страницы: 13

Бренд: Vivo Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды