manualshive.com logo in svg

HP A7L26UT#ABA, Руководство по техническому обслуживанию и ремонту

"HP A7L26UT#ABA" - это надежный и производительный ноутбук, идеально подходящий для работы и развлечений. На нашем сайте вы можете бесплатно скачать брошюру и руководство пользователя для этого устройства. Посетите {веб-сайт} и получите всю необходимую информацию для комфортного использования ноутбука.

Поделиться
Скачать
background image

Solving Network Problems

Some common causes and solutions for network problems are listed in the following table. These
guidelines do not discuss the process of debugging the network cabling.

Table D-12

  Solving Network Problems

Wake-on-LAN feature is not functioning.

Cause

Solution

S5 Maximum Power Saving feature is enabled.

Disable the S5 Maximum Power Saving option in Computer
Setup. Select 

Power

 

>

 

Hardware Power Management

 

>

 

S5

Maximum Power Saving

.

S5 Wake on LAN is disabled.

: Enable the S5 Wake on LAN option in Computer Setup.
Select 

Advanced

 > 

Device Options

 > 

S5 Wake on LAN

.

Wake-on-LAN is not enabled.

To enable Wake-on-LAN:

1.

Select 

Start

 > 

Control Panel

.

2.

Under 

Network and Internet

, select 

View network

status and tasks

.

3.

Click 

Local Area Connection

.

4.

Click the 

Properties

 button.

5.

Click the 

Configure

 button.

6.

Click the 

Power Management

 tab, then select the

check box to 

Allow this device to wake the computer

.

Network driver does not detect network controller.

Cause

Solution

Network controller is disabled.

1.

Run Computer Setup and enable network controller.

2.

Enable the network controller in the operating system
via Device Manager.

Incorrect network driver.

Check the network controller documentation for the correct
driver or obtain the latest driver from the manufacturer’s Web
site.

Network status link light never flashes.

NOTE:

The network status light is supposed to flash when there is network activity.

Cause

Solution

No active network is detected.

Check cabling and network equipment for proper connection.

Network controller is not set up properly.

Check for the device status within Windows, such as Device
Manager for driver load and the Network Connections applet
within Windows for link status.

Solving Network Problems 165

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

Barco PWS-101 Specifications preview
PWS-101
Бренд: Barco Страницы: 2
Pinnacle Systems Deko1000 Technical Reference And Service Manual preview
Deko1000
Бренд: Pinnacle Systems Страницы: 102
C&T Solution ACO-6000-8L User Manual preview
ACO-6000-8L
Бренд: C&T Solution Страницы: 108
eMachines eMonster 500 Supplement Manual preview
eMonster 500
Бренд: eMachines Страницы: 36
Gigabyte BRIX IoT Quick Start Manual preview
BRIX IoT
Бренд: Gigabyte Страницы: 2
Go!Paint FlowControl FC-S01 Original Operating Manual preview
FlowControl FC-S01
Бренд: Go!Paint Страницы: 20
Franklin ACE 500 User'S Reference Manual preview
ACE 500
Бренд: Franklin Страницы: 171
Sun Microsystems Sun Ultra 450 Manual preview
Sun Ultra 450
Бренд: Sun Microsystems Страницы: 45
Vivo DESK-V000U Instruction Manual preview
DESK-V000U
Бренд: Vivo Страницы: 3
Avid Technology HP Z220 Configuration Manuallines preview
HP Z220
Бренд: Avid Technology Страницы: 19
HP ProDesk 400 G4 Hardware Reference Manual preview
ProDesk 400 G4
Бренд: HP Страницы: 53
Honeywell 120 Hardware Manual preview
120
Бренд: Honeywell Страницы: 100
Gateway DX420QS Setting Up preview
DX420QS
Бренд: Gateway Страницы: 2
Gateway dx4870 User Manual preview
dx4870
Бренд: Gateway Страницы: 98
Gateway GM5407H User Manual preview
GM5407H
Бренд: Gateway Страницы: 190
Tek Panel LCD Computer and Touchscreen Specification preview
LCD Computer and Touchscreen
Бренд: Tek Panel Страницы: 2
Silicon Graphics 320 Owner'S Manual preview
320
Бренд: Silicon Graphics Страницы: 152
Silicon Graphics IRIS Workstation User Manual preview
IRIS Workstation
Бренд: Silicon Graphics Страницы: 170

Бренды по названию

Популярные бренды

Загрузить еще бренды