HP A7L26UT#ABA Скачать руководство пользователя страница 154 | Manualshive

Страница: 154 / 200

background image

There is no sound or sound volume is too low.

Cause

Solution

System volume may be set low or muted.

1.

Check the F10 BIOS settings to make sure the internal
system speaker is not muted (this setting does not
affect the external speakers).

2.

Make sure the external speakers are properly
connected and powered on and that the speakers'
volume control is set correctly.

3.

Use the system volume control available in the
operating system to make sure the speakers are not
muted or to increase the volume.

Poor performance is experienced.

Cause

Solution

Processor is hot.

1.

Make sure airflow to the computer is not blocked. Leave
a 10.2-cm (4-inch) clearance on all vented sides of the
computer and above the monitor to permit the required
airflow.

2.

Make sure fans are connected and working properly
(some fans only operate when needed).

3.

Make sure the processor heat sink is installed properly.

Hard drive is full.

Transfer data from the hard drive to create more space on
the hard drive.

Low on memory.

Add more memory.

Hard drive fragmented.

Defragment hard drive.

Program previously accessed did not release reserved
memory back to the system.

Restart the computer.

Virus resident on the hard drive.

Run virus protection program.

Too many applications running.

1.

Close unnecessary applications to free up memory.

2.

Add more memory. Some applications run in the
background and can be closed by right-clicking on their
corresponding icons in the task tray. To prevent these
applications from launching at startup, go to

Start

>

All

Programs

>

Accessories

>

Run

and type

msconfig

.

On the

Startup

tab of the System Configuration Utility,

clear applications that you do not want to launch
automatically.

Some software applications, especially games, are stressful
on the graphics subsystem

1.

Lower the display resolution for the current application
or consult the documentation that came with the
application for suggestions on how to improve
performance by adjusting parameters in the application.

2.

Add more memory.

3.

Upgrade the graphics solution.

Cause unknown.

Restart the computer.

144 Appendix D Troubleshooting Without Diagnostics

«
...
152
153
154
155
156
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

Бренд: Acer Страницы: 20

Бренд: Acer Страницы: 20

Бренд: Acer Страницы: 18

Бренд: Acer Страницы: 30

PowerMate 2000 Series

Бренд: NEC Страницы: 8

Бренд: NEC Страницы: 8

DIRECTION L - SERVICE

Бренд: NEC Страницы: 139

Бренд: IBM Страницы: 252

Бренд: Layher Страницы: 6

Бренд: Gateway Страницы: 164

Бренд: Gateway Страницы: 176

Бренд: Advantech Страницы: 50

Бренд: IBM Страницы: 314

Бренд: Vivo Страницы: 5

Бренд: GREER Company Страницы: 18

Бренд: Asus Страницы: 66

Essentio CM5571

Бренд: Asus Страницы: 122

Бренд: Asus Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды