HP A7L26UT#ABA Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 200

background image

7

Removal and Replacement Procedures
– Microtower Chassis

Adherence to the procedures and precautions described in this chapter is essential for proper service.
After completing all necessary removal and replacement procedures, run the Diagnostics utility to
verify that all components operate properly.

NOTE:

Not all features listed in this guide are available on all computers.

Serviceability Features

The computers include features that make them easy to upgrade and service. A Torx T-15, Phillips,
or flat blade screwdriver is needed for many of the installation procedures described in this guide.

Preparation for Disassembly

1.

Close any open software applications.

2.

Exit the operating system.

3.

Remove any diskette or compact disc from the computer.

4.

Turn off the computer and any peripheral devices that are connected to it.

CAUTION:

Turn off the computer before disconnecting any cables.

CAUTION:

Regardless of the power-on state, voltage is always present on the system board

as long as the system is plugged into an active AC outlet. In some systems the cooling fan is on
even when the computer is in the “Standby,” or “Suspend” modes. The power cord should
always be disconnected before servicing a unit.

5.

Disconnect the power cord from the electrical outlet and then from the computer.

6.

Disconnect all peripheral device cables from the computer.

NOTE:

During disassembly, label each cable as you remove it, noting its position and routing.

Keep all screws with the units removed.

CAUTION:

The screws used in the computer are of different thread sizes and lengths; using

the wrong screw in an application may damage the unit.

42

Chapter 7 Removal and Replacement Procedures – Microtower Chassis

«
...
50
51
52
53
54
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

Бренд: Kaypro Страницы: 157

Бренд: IBM Страницы: 212

9228 - IntelliStation Z - Pro

Бренд: IBM Страницы: 72

9114-275 - IntelliStation POWER 275

Бренд: IBM Страницы: 102

8863 - eServer xSeries 366

Бренд: IBM Страницы: 94

Бренд: IBM Страницы: 4

Бренд: IBM Страницы: 84

Бренд: IBM Страницы: 96

Бренд: IBM Страницы: 156

Бренд: IBM Страницы: 178

Бренд: IBM Страницы: 155

Бренд: IBM Страницы: 214

Бренд: Ocean Systems Страницы: 2

Бренд: Zotac Страницы: 57

Бренд: Winmate Страницы: 20

Бренд: dji Страницы: 14

Бренд: Silicon Graphics Страницы: 152

IRIS Workstation

Бренд: Silicon Graphics Страницы: 170

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды