HP A7L26UT#ABA Скачать руководство пользователя страница 144 | Manualshive

Страница: 144 / 200

background image

Table C-1

Numeric Codes and Text Messages (continued)

Control panel message

Description

Recommended action

2211-Memory not configured correctly for
proper MEBx execution.

DIMM1 or XMM1 is not installed.

Make sure there is a memory module in the
black DIMM1 socket and that it is properly
seated.

2212-USB Key Provisioning failure writing to
device

USB device used for USB key provisioning
will not allow BIOS to update provision file
properly.

1.

Try a different USB key device for
provisioning.

2.

If the error persists, update to the latest
BIOS version and ME firmware
version.

3.

If the error still persists, replace the
system board.

2217-ME Firmware Version request failure

ME firmware is not properly responding to
BIOS query for version information.

1.

Reboot the computer.

2.

If the error persists, update to the latest
BIOS version and ME firmware
version.

3.

If the error still persists, replace the
system board.

2218-ME Firmware Version should be
updated

ME firmware must be updated to match
current functionality contained in the system
BIOS.

1.

Update to the latest ME firmware
version.

2.

If the error persists and system BIOS
has been recently updated, restore
previous system BIOS version.

3.

If the error still persists, replace the
system board.

2219-USB Key Provisioning file has invalid
header identifier

Provisioning file contained on the USB key
has been corrupted or is not a valid version
for the current ME firmware.

1.

Recreate the provisioning file using
third party management console
software.

2.

If the error persists and system BIOS
has been recently updated, restore
previous system BIOS version.
Otherwise, update the ME firmware
version.

3.

If the error still persists, replace the
system board.

2220-USB Key Provisioning file has
mismatch version

Provisioning file contained on the USB key
is not a valid version for the current ME
firmware.

1.

Reboot the computer.

2.

If the error persists and system BIOS
has been recently updated, restore
previous system BIOS version.
Otherwise, update the ME firmware
version.

3.

If the error still persists, replace the
system board.

134 Appendix C POST Error Messages

«
...
142
143
144
145
146
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

Бренд: Safco Страницы: 2

Бренд: PMC Страницы: 126

Бренд: Antec Страницы: 10

NUC 11 Performance

Бренд: Intel Страницы: 20

DeviceEdge Mini AIE-C011

Бренд: Aetina Страницы: 14

Бренд: Compaq Страницы: 20

IFO2175-873 Series

Бренд: AXIOMTEK Страницы: 70

Бренд: Advantech Страницы: 44

DECstaion 5000 240

Бренд: Digital Equipment Страницы: 62

Бренд: Intel Страницы: 2

Бренд: Ruijie Networks Страницы: 30

Integrated Touchscreen Computer J2 650

Бренд: J2 Страницы: 78

Бренд: Biostar Страницы: 42

Бренд: Moxa Technologies Страницы: 6

Plug PC LXP 2310

Бренд: Chip PC Страницы: 4

Бренд: HONEYWELL BULL Страницы: 73

Tank GT20 (B5211)

Бренд: TYAN Страницы: 73

Бренд: Shuttle Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды