HP A7L26UT#ABA Скачать руководство пользователя страница 166

Страница: 166 / 200

“No Connection, Check Signal Cable” displays on screen.

Cause

Solution

Monitor video cable is disconnected.

Connect the video cable between the monitor and computer.

CAUTION:

Ensure that the computer power is off while

connecting the video cable.

“Out of Range” displays on screen.

Cause

Solution

Video resolution and refresh rate are set higher than what
the monitor supports.

Restart the computer and enter Safe Mode. Change the
settings to a supported setting then restart the computer so
that the new settings take effect.

Vibrating or rattling noise coming from inside a CRT monitor when powered on.

Cause

Solution

Monitor degaussing coil has been activated.

None. It is normal for the degaussing coil to be activated
when the monitor is powered on.

Clicking noise coming from inside a CRT monitor.

Cause

Solution

Electronic relays have been activated inside the monitor.

None. It is normal for some monitors to make a clicking noise
when turned on and off, when going in and out of standby
mode, and when changing resolutions.

High pitched noise coming from inside a flat panel monitor.

Cause

Solution

Brightness and/or contrast settings are too high.

Lower brightness and/or contrast settings.

156 Appendix D Troubleshooting Without Diagnostics

Содержание A7L26UT#ABA









































































































































































































Результаты поиска

Содержание A7L26UT#ABA

Отзывы:

Похожие инструкции для A7L26UT#ABA

Бренды по названию

Популярные бренды

HP A7L26UT#ABA, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание A7L26UT#ABA

Отзывы:

Похожие инструкции для A7L26UT#ABA

Бренды по названию

Популярные бренды