HP A7L26UT#ABA Скачать руководство пользователя страница 146 | Manualshive

Страница: 146 / 200

background image

Table C-1

Numeric Codes and Text Messages (continued)

Control panel message

Description

Recommended action

Network Server Mode Active and No
Keyboard Attached

Keyboard failure while Network Server
Mode enabled.

1.

Reconnect keyboard with computer
turned off.

2.

Check connector for bent or missing
pins.

3.

Ensure that none of the keys are
depressed.

4.

Replace keyboard.

Parity Check 2

Parity RAM failure.

Run Computer Setup and Diagnostic
utilities.

Interpreting POST Diagnostic Front Panel LEDs and

Audible Codes

This section covers the front panel LED codes as well as the audible codes that may occur before or
during POST that do not necessarily have an error code or text message associated with them.

WARNING!

When the computer is plugged into an AC power source, voltage is always applied to

the system board. To reduce the risk of personal injury from electrical shock and/or hot surfaces, be
sure to disconnect the power cord from the wall outlet and allow the internal system components to
cool before touching.

NOTE:

If you see flashing LEDs on a PS/2 keyboard, look for flashing LEDs on the front panel of

the computer and refer to the following table to determine the front panel LED codes.

Recommended actions in the following table are listed in the order in which they should be
performed.

Not all diagnostic lights and audible codes are available on all models.

Table C-2

Diagnostic Front Panel LEDs and Audible Codes

Activity

Beeps

Possible Cause

Recommended Action

Green Power LED On.

None

Computer on.

None

Green Power LED flashes
every two seconds.

None

Computer in Suspend to
RAM mode (some models
only) or normal Suspend
mode.

None required. Press any key or move the
mouse to wake the computer.

136 Appendix C POST Error Messages

«
...
144
145
146
147
148
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

TitraLab KF1000 Series

Бренд: Hach Страницы: 68

TitraLab AT1102

Бренд: Hach Страницы: 158

EBOX-335xDX3 Series

Бренд: DMP Electronics Страницы: 40

Бренд: Medion Страницы: 2

Бренд: StarTech.com Страницы: 29

Бренд: Vector Страницы: 32

Бренд: HP Страницы: 1

Pavilion 400 - Desktop PC

Бренд: HP Страницы: 2

Pavilion 400 - Desktop PC

Бренд: HP Страницы: 2

Бренд: HP Страницы: 6

Бренд: HP Страницы: 1

Бренд: HP Страницы: 1

Бренд: HP Страницы: 7

Бренд: HP Страницы: 1

Omni 100-5200 - Desktop PC

Бренд: HP Страницы: 1

Бренд: HP Страницы: 1

Бренд: HP Страницы: 7

Бренд: HP Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды