HP A7L26UT#ABA Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 200

background image

●

Solve system configuration errors detected but not automatically fixed during the Power-On Self-
Test (POST).

●

Replicate the system setup by saving system configuration information on a USB device and
restoring it on one or more computers.

●

Execute self-tests on a specified ATA hard drive (when supported by drive).

●

Enable or disable DriveLock security (when supported by drive).

Using Computer Setup (F10) Utilities

Computer Setup can be accessed only by turning the computer on or restarting the system.
To access the Computer Setup Utilities menu, complete the following steps:

1.

Turn on or restart the computer. If you are in Microsoft Windows, click

Start

>

Shut Down

>

Restart

.

2.

Press either

Esc

or

F10

while the “Press the ESC key for Startup Menu” message is displayed at

the bottom of the screen.

Pressing

Esc

displays a menu that allows you to access different options available at startup.

NOTE:

If you do not press

Esc

or

F10

at the appropriate time, you must restart the computer

and again press

Esc

or

F10

when the monitor light turns green to access the utility.

3.

If you pressed

Esc

, press

F10

to enter Computer Setup.

4.

A choice of five headings appears in the Computer Setup Utilities menu: File, Storage, Security,
Power, and Advanced.

5.

Use the arrow (left and right) keys to select the appropriate heading. Use the arrow (up and
down) keys to select the option you want, then press

Enter

. To return to the Computer Setup

Utilities menu, press

Esc

.

6.

To apply and save changes, select

File

>

Save Changes and Exit

.

●

If you have made changes that you do not want applied, select

Ignore Changes and Exit

.

●

To reset to factory settings or previously saved default settings (some models), select

Apply Defaults and Exit

. This option will restore the original factory system defaults.

CAUTION:

Do NOT turn the computer power OFF while the BIOS is saving the Computer Setup

(F10) changes because the CMOS could become corrupted. It is safe to turn off the computer only
after exiting the F10 Setup screen.

Table 3-1

Computer Setup (F10) Utility

Heading

Table

File

Computer Setup—File on page 9

Storage

Computer Setup—Storage on page 10

Security

Computer Setup—Security on page 12

Power

Computer Setup—Power on page 15

Advanced

Computer Setup—Advanced on page 16

8

Chapter 3 Computer Setup (F10) Utility

«
...
16
17
18
19
20
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

POWERMATE - VERSION 2008

Бренд: NEC Страницы: 32

Бренд: Radio Shack Страницы: 40

Бренд: Oval Страницы: 18

Бренд: Wacom Страницы: 340

Бренд: Aaeon Страницы: 89

Cabling Sitting/Standing Workstation

Бренд: VS Страницы: 8

PCV-R532DS - Vaio Digital Studio Desktop Computer

Бренд: Sony Страницы: 1

PCV-R526DS - Vaio Digital Studio Desktop Computer

Бренд: Sony Страницы: 1

PCV-LX920 - Vaio Slimtop Computer

Бренд: Sony Страницы: 1

PCV-LX910 - Vaio Slimtop Computer

Бренд: Sony Страницы: 1

PCV-LX810 - Vaio Slimtop Computer

Бренд: Sony Страницы: 1

PCV-LX800 - VAIO - 128 MB RAM

Бренд: Sony Страницы: 1

PCV-LX700 - Vaio Slimtop Computer

Бренд: Sony Страницы: 1

PCV-R526DS - Vaio Digital Studio Desktop Computer

Бренд: Sony Страницы: 33

PCV-LX810 - Vaio Slimtop Computer

Бренд: Sony Страницы: 39

PCV-RS700C - Vaio Desktop Computer

Бренд: Sony Страницы: 161

PCV-MXS20 Online Help Center (VAIO User Guide)

Бренд: Sony Страницы: 113

PCV-LX700 - Vaio Slimtop Computer

Бренд: Sony Страницы: 110

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды