HP A7L26UT#ABA Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 200

background image

Computer will not boot from hard drive.

Cause

Solution

The device is attached to a SATA port that has been hidden
in Computer Setup.

Run the Computer Setup utility and ensure

Device Available

is selected for the device's SATA port in

Security

>

Device

Security

.

Boot order is not correct.

Run the Computer Setup utility and change boot sequence in

Storage

>

Boot Order

.

Hard Drive's “Emulation Type” is set to “None.”

Run the Computer Setup utility and change the “Emulation
Type” to “Hard Disk” in the device's details under

Storage

>

Device Configuration

.

Hard drive is damaged.

Observe if the front panel Power LED is blinking RED and if
any beeps are heard. See Appendix A,

POST Error

Messages on page 127

to determine possible causes for the

blinking red and beep codes.

See the Worldwide Limited Warranty for terms and
conditions.

Computer seems to be locked up.

Cause

Solution

Program in use has stopped responding to commands.

Attempt the normal Windows “Shut Down” procedure. If this
fails, press the power button for four or more seconds to turn
off the power. To restart the computer, press the power
button again.

The removable hard drive has no power to the hard drive enclosure.

Cause

Solution

The lock on the enclosure is not turned to the “ON” position.

Insert the key and turn the lock clockwise 90 degrees. The
green LED on the front of the enclosure should be on.

Power cable from the computer power supply to the
enclosure frame is not properly connected.

Check the power supply to make sure it is properly
connected to the rear of the enclosure frame.

The removable hard drive is not recognized by the computer.

Cause

Solution

The removable hard drive carrier is not fully seated in the
enclosure frame or the hard drive is not fully seated in the
carrier.

Push the carrier into the enclosure frame so that the
connector on the rear of the frame is properly seated. If this
does not solve the problem, turn off the computer, remove
the carrier, and check to see if the connector on the hard
drive is properly seated in the carrier.

Solving Hard Drive Problems 151

«
...
159
160
161
162
163
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

Бренд: BAC Страницы: 24

Бренд: EUROCOM Страницы: 1

Бренд: C&T Solution Страницы: 108

Бренд: eMachines Страницы: 36

Бренд: Sysgration Страницы: 27

EloPOS 15'' Series

Бренд: Elo Touch Solutions Страницы: 39

Бренд: XPLORE TECHNOLOGIES Страницы: 2

Бренд: Vivo Страницы: 16

Бренд: Vivo Страницы: 4

Бренд: Clarke Страницы: 8

DA-682A-DPP Series

Бренд: Moxa Technologies Страницы: 7

Бренд: WeWi Страницы: 29

Бренд: Trident Страницы: 20

QBiX2-Pro-APLB4200H-A1

Бренд: GIGAIPC Страницы: 73

Бренд: Embedded computer Source Страницы: 37

Бренд: Avigilon Страницы: 11

iStick A300 Series

Бренд: PQ Labs Страницы: 3

Бренд: IBM Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды