HP A7L26UT#ABA Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 200

background image

Operating Guidelines

To prevent overheating and to help prolong the life of the computer:

●

Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and
cold.

●

Operate the computer on a sturdy, level surface. Leave a 10.2-cm (4-inch) clearance on all
vented sides of the computer and above the monitor to permit the required airflow.

●

Never restrict the airflow into the computer by blocking any vents or air intakes. Do not place the
keyboard, with the keyboard feet down, directly against the front of the desktop unit as this also
restricts airflow.

●

Occasionally clean the air vents on all vented sides of the computer. Lint, dust, and other foreign
matter can block the vents and limit the airflow. Be sure to unplug the computer before cleaning
the air vents.

●

Never operate the computer with the cover or side panel removed.

●

Do not stack computers on top of each other or place computers so near each other that they
are subject to each other’s re-circulated or preheated air.

●

If the computer is to be operated within a separate enclosure, intake and exhaust ventilation
must be provided on the enclosure, and the same operating guidelines listed above will still
apply.

●

Keep liquids away from the computer and keyboard.

●

Never cover the ventilation slots on the monitor with any type of material.

●

Install or enable power management functions of the operating system or other software,
including sleep states.

Routine Care

General Cleaning Safety Precautions

1.

Never use solvents or flammable solutions to clean the computer.

2.

Never immerse any parts in water or cleaning solutions; apply any liquids to a clean cloth and
then use the cloth on the component.

3.

Always unplug the computer when cleaning with liquids or damp cloths.

4.

Always unplug the computer before cleaning the keyboard, mouse, or air vents.

5.

Disconnect the keyboard before cleaning it.

6.

Wear safety glasses equipped with side shields when cleaning the keyboard.

Cleaning the Computer Case

Follow all safety precautions in

General Cleaning Safety Precautions on page 38

before cleaning the

computer.

38

Chapter 6 Routine Care and Disassembly Preparation

«
...
46
47
48
49
50
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

c3700 - Workstation

Бренд: Ace Страницы: 21

Mac Mini Model A1347

Бренд: iFixit Страницы: 13

Elements Workstation 3 Person Run

Бренд: Jason.L Страницы: 5

Бренд: Worx Professional Страницы: 106

Бренд: Dell Страницы: 121

Бренд: Aaeon Страницы: 89

Бренд: KME Страницы: 2

Бренд: Packard Bell Страницы: 13

Бренд: Packard Bell Страницы: 15

Бренд: Technologic Systems Страницы: 35

Бренд: National Instruments Страницы: 37

Бренд: Inspur Страницы: 2

kontron COMe-cVR6

Бренд: S&T Страницы: 90

Бренд: Packard Bell Страницы: 66

Бренд: Hangzhou Ruideng Technology Co., Ltd. Страницы: 9

Бренд: AMSTRAD Страницы: 52

Бренд: Autodesk Страницы: 54

Бренд: IBM Страницы: 230

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды