HP A7L26UT#ABA Скачать руководство пользователя страница 173 | Manualshive

Страница: 173 / 200

background image

Solving Hardware Installation Problems

You may need to reconfigure the computer when you add or remove hardware, such as an additional
drive or expansion card. If you install a plug and play device, Windows automatically recognizes the
device and configures the computer. If you install a non–plug and play device, you must reconfigure
the computer after completing installation of the new hardware. In Windows, use the

Add Hardware

Wizard

and follow the instructions that appear on the screen.

WARNING!

When the computer is plugged into an AC power source, voltage is always applied to

the system board. To reduce the risk of personal injury from electrical shock and/or hot surfaces, be
sure to disconnect the power cord from the wall outlet and allow the internal system components to
cool before touching.

Table D-11

Solving Hardware Installation Problems

A new device is not recognized as part of the system.

Cause

Solution

Device is not seated or connected properly.

Ensure that the device is properly and securely connected
and that pins in the connector are not bent down.

Cable(s) of new external device are loose or power cables
are unplugged.

Ensure that all cables are properly and securely connected
and that pins in the cable or connector are not bent down.

Power switch of new external device is not turned on.

Turn off the computer, turn on the external device, then turn
on the computer to integrate the device with the computer
system.

When the system advised you of changes to the
configuration, you did not accept them.

Reboot the computer and follow the instructions for
accepting the changes.

A plug and play board may not automatically configure when
added if the default configuration conflicts with other devices.

Use Windows Device Manager to deselect the automatic
settings for the board and choose a basic configuration that
does not cause a resource conflict. You can also use
Computer Setup to reconfigure or disable devices to resolve
the resource conflict.

USB ports on the computer are disabled in Computer Setup.

Run the Computer Setup utility and ensure that

Device

available

is selected for appropriate USB ports under

Security

>

USB Security

.

Computer will not start.

Cause

Solution

Wrong memory modules were used in the upgrade or
memory modules were installed in the wrong location.

1.

Review the documentation that came with the system to
determine if you are using the correct memory modules
and to verify the proper installation.

NOTE:

DIMM1 or XMM1 must always be installed.

2.

Observe the beeps and LED lights on the front of the
computer. Beeps and flashing LEDs are codes for
specific problems.

3.

If you still cannot resolve the issue, contact Customer
Support.

Solving Hardware Installation Problems 163

«
...
171
172
173
174
175
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

Бренд: IBM Страницы: 78

Бренд: IBM Страницы: 76

Бренд: IBM Страницы: 72

Бренд: IBM Страницы: 66

Бренд: IBM Страницы: 70

Бренд: IBM Страницы: 56

Бренд: IBM Страницы: 72

Бренд: IBM Страницы: 78

Бренд: IBM Страницы: 52

Бренд: IBM Страницы: 118

Бренд: IBM Страницы: 114

Бренд: IBM Страницы: 46

Бренд: IBM Страницы: 116

Бренд: IBM Страницы: 118

Бренд: IBM Страницы: 90

Бренд: IBM Страницы: 86

Бренд: IBM Страницы: 88

Бренд: IBM Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды