HP A7L26UT#ABA Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 200

background image

7.

If you are not installing a new expansion card, install an expansion slot cover to close the open
slot.

CAUTION:

After removing an expansion card, you must replace it with a new card or

expansion slot cover for proper cooling of internal components during operation.

8.

To install a new expansion card, hold the card just above the expansion socket on the system
board then move the card toward the rear of the chassis so that the bottom of the bracket on the
card slides into the small slot on the chassis. Press the card straight down into the expansion
socket on the system board.

Figure 7-11

Installing an Expansion Card

NOTE:

When installing an expansion card, press firmly on the card so that the whole

connector seats properly in the expansion card slot.

9.

Replace the slot cover lock and secure it in place with the screw that was previously removed.

Figure 7-12

Securing the Expansion Cards and Slot Covers

54

Chapter 7 Removal and Replacement Procedures – Microtower Chassis

«
...
62
63
64
65
66
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

POWERMATE - VERSION 2007

Бренд: NEC Страницы: 31

Бренд: Olivetti Страницы: 118

Бренд: Risecom Corporation Страницы: 32

Бренд: EUROCOM Страницы: 176

Бренд: DFI Страницы: 15

Бренд: Elo TouchSystems Страницы: 3

Бренд: Vivo Страницы: 5

ideaCentre N308

Бренд: Lenovo Страницы: 29

ideaCentre N300

Бренд: Lenovo Страницы: 30

Бренд: Lenovo Страницы: 37

IdeaCentre K200

Бренд: Lenovo Страницы: 32

IdeaCentre K3 Series

Бренд: Lenovo Страницы: 47

IdeaCentre Q Series

Бренд: Lenovo Страницы: 55

IdeaCentre Horizon 27 Series

Бренд: Lenovo Страницы: 47

IdeaCentre K410

Бренд: Lenovo Страницы: 65

IdeaCentre K4 Series

Бренд: Lenovo Страницы: 69

Бренд: Lenovo Страницы: 142

Бренд: Lenovo Страницы: 453

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды