HP A7L26UT#ABA Скачать руководство пользователя страница 153 | Manualshive

Страница: 153 / 200

background image

Solving General Problems

You may be able to easily resolve the general problems described in this section. If a problem
persists and you are unable to resolve it yourself or if you feel uncomfortable about performing the
operation, contact an authorized dealer or reseller.

WARNING!

When the computer is plugged into an AC power source, voltage is always applied to

the system board. To reduce the risk of personal injury from electrical shock and/or hot surfaces, be
sure to disconnect the power cord from the wall outlet and allow the internal system components to
cool before touching.

Table D-1

Solving General Problems

Computer appears locked up and will not turn off when the power button is pressed.

Cause

Solution

Software control of the power switch is not functional.

1.

Press and hold the power button for at least four
seconds until the computer turns off.

2.

Disconnect the power cord from the electrical outlet.

Computer will not respond to USB keyboard or mouse.

Cause

Solution

Computer is in

standby

mode.

To resume from

standby

mode, press the power button or

press any key.

CAUTION:

When attempting to resume from

standby

mode, do not hold down the power button for more than four
seconds. Otherwise, the computer will shut down and you
will lose any unsaved data.

System has locked up.

Restart computer.

Computer date and time display is incorrect.

Cause

Solution

RTC (real-time clock) battery may need to be replaced.

NOTE:

Connecting the computer to a live AC outlet

prolongs the life of the RTC battery.

First, reset the date and time under

Control Panel

(Computer Setup can also be used to update the RTC date
and time). If the problem persists, replace the RTC battery.
See the Removal and Replacement section for instructions
on installing a new battery, or contact an authorized dealer or
reseller for RTC battery replacement.

Cursor will not move using the

arrow

keys on the keypad.

Cause

Solution

The

Num Lock

key may be on.

Press the

Num Lock

key. The Num Lock light should not be

on if you want to use the

arrow

keys. The

Num Lock

key can

be disabled (or enabled) in Computer Setup.

Solving General Problems 143

«
...
151
152
153
154
155
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

FPMA-MOBILE1800

Бренд: New Star Computer Products Страницы: 4

Бренд: WinSystems Страницы: 53

Бренд: GARANT Страницы: 60

Бренд: 7starlake Страницы: 31

Бренд: Ergotron Страницы: 20

Бренд: NexAIoT Страницы: 71

Бренд: StarTech.com Страницы: 6

Бренд: Daikin Страницы: 48

Бренд: Zotac Страницы: 33

Бренд: Dell EMC Страницы: 90

Бренд: ZIPPER MASCHINEN Страницы: 6

Бренд: IEI Technology Страницы: 99

Бренд: U-Line Страницы: 12

Бренд: U-Line Страницы: 21

Бренд: U-Line Страницы: 24

Jackson Desk TD2000-AC

Бренд: WB Manufacturing Страницы: 2

Бренд: Icop Страницы: 32

Бренд: MSI Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды