HP A7L26UT#ABA Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 200

background image

6.

If using a new fan sink, remove the protective covering from the bottom of the fan sink and place
it in position atop the processor.

7.

Secure the fan sink to the system board and system board tray.

CAUTION:

Fan sink retaining screws should be tightened in diagonally opposite pairs (as in an

X) to evenly seat the fan sink on the processor. This is especially important as the pins on the
socket are very fragile and any damage to them may require replacing the system board.

NOTE:

After installing a new processor onto the system board, always update the system ROM to

ensure that the latest version of the BIOS is being used on the computer. The latest system BIOS can
be found on the Web at:

http://h18000.www1.hp.com/support/files

.

Power Supply

Description

Spare part number

Power supply, 220W

656722-001

Power supply, 270W

665224-001

WARNING!

To reduce potential safety issues, only the power supply provided with the computer, a

replacement power supply provided by HP, or a power supply purchased as an accessory from HP
should be used with the computer.

The rotating power supply is located at the rear of the chassis. It is held in place by a bracket – no
screws are used.

WARNING!

Voltage is always present on the system board when the computer is plugged into an

active AC outlet. To avoid possible personal injury and damage to the equipment the power cord
should be disconnected from the computer and/or the AC outlet before opening the computer.

The power supply is secured to the rear of the computer with four Torx screws. On the inside of the
computer, a tab secures the power supply to the base pan.

1.

Prepare the computer for disassembly (

Preparation for Disassembly on page 79

).

2.

Remove the access panel (

Access Panel on page 80

).

3.

Rotate the drive cage up and disconnect the power cables from all of the drives.

4.

Disconnect the power cables from the system board as follows:

●

white 24-pin labeled P1 from ATX_POWER system board connector

●

white 4-pin labeled P2 from ATX_CPU system board connector

112 Chapter 8 Removal and Replacement Procedures – Small Form Factor (SFF) Chassis

«
...
120
121
122
123
124
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

Бренд: Wasp Barcode Technologies Страницы: 69

D-3362-I Series

Бренд: Icop Страницы: 14

Бренд: Aaeon Страницы: 64

Бренд: Lanoptik Страницы: 16

Бренд: Iron Age Office Страницы: 7

Height Adjustable Standing Desk 4-Leg

Бренд: Uplift Desk Страницы: 16

Бренд: Korg Страницы: 233

Бренд: Allen-Bradley Страницы: 34

Бренд: Silicon Graphics Страницы: 152

IRIS Workstation

Бренд: Silicon Graphics Страницы: 170

Бренд: Ergotron Страницы: 20

Бренд: DM&P Group Страницы: 27

Stockholm Micro Desk

Бренд: FRISKA Страницы: 20

Eko Workstation

Бренд: Knight Страницы: 6

Бренд: Terra Страницы: 136

Бренд: Advantech Страницы: 52

Бренд: Advantech Страницы: 55

Бренд: Advantech Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды