HP A7L26UT#ABA Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 200

background image

Table C-2

Diagnostic Front Panel LEDs and Audible Codes (continued)

Activity

Beeps

Possible Cause

Recommended Action

Red Power LED flashes five
times, once every second,
followed by a two second
pause. Beeps stop after fifth
iteration but LEDs continue
until problem is solved.

5

Pre-video memory error.

CAUTION:

To avoid damage to the DIMMs or

the system board, you must unplug the computer
power cord before attempting to reseat, install, or
remove a DIMM module.

1.

Reseat DIMMs.

2.

Replace DIMMs one at a time to isolate the
faulty module.

3.

Replace third-party memory with HP
memory.

4.

Replace the system board.

Red Power LED flashes six
times, once every second,
followed by a two second
pause. Beeps stop after fifth
iteration but LEDs continue
until problem is solved.

6

Pre-video graphics error.

For systems with a graphics card:

1.

Reseat the graphics card.

2.

Replace the graphics card.

3.

Replace the system board.

For systems with integrated graphics, replace
the system board.

Red Power LED flashes
seven times, once every
second, followed by a two
second pause. Beeps stop
after fifth iteration but LEDs
continue until problem is
solved.

7

System board failure
(ROM detected failure
prior to video).

Replace the system board.

Red Power LED flashes eight
times, once every second,
followed by a two second
pause. Beeps stop after fifth
iteration but LEDs continue
until problem is solved.

8

Invalid ROM based on
bad checksum.

1.

Reflash the system ROM with the latest
BIOS image. See the “Boot Block
Emergency Recovery Mode” section of the

Desktop Management Guide

for more

information.

2.

Replace the system board.

Red Power LED flashes nine
times, once every second,
followed by a two second
pause. Beeps stop after fifth
iteration but LEDs continue
until problem is solved.

9

System powers on but is
unable to boot.

1.

Check that the voltage selector, located on
the rear of the power supply (some
models), is set to the appropriate voltage.
Proper voltage setting depends on your
region.

2.

Unplug the AC power cord from the
computer, wait 30 seconds, then plug the
power cord back in to the computer.

3.

Replace the system board.

4.

Replace the processor.

138 Appendix C POST Error Messages

«
...
146
147
148
149
150
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

Бренд: Canon Страницы: 160

Бренд: Olivetti Страницы: 111

Бренд: Panasonic Страницы: 15

Бренд: Harbor Freight Tools Страницы: 4

System x3200 M3

Бренд: IBM Страницы: 42

Бренд: EUROCOM Страницы: 113

Бренд: IBM Страницы: 190

Presario 3500 Series

Бренд: Compaq Страницы: 68

Бренд: Stage right Страницы: 12

Бренд: easescreen Страницы: 4

DWL-P1012 - Power Injector - 185 Watt

Бренд: D-Link Страницы: 51

Integrated Touchscreen Computer J2 650

Бренд: J2 Страницы: 78

RY883AA#ABA - Compaq Presario - SR5002HM

Бренд: HP Страницы: 1

RY883AA#ABA - Compaq Presario - SR5002HM

Бренд: HP Страницы: 2

Envy Recline23 TouchSmart Beats SE All-in-One

Бренд: HP Страницы: 5

ENVY Phoenix 850

Бренд: HP Страницы: 11

Бренд: HP Страницы: 2

Envy Phoenix 800

Бренд: HP Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды