HP A7L26UT#ABA Скачать руководство пользователя страница 177 | Manualshive

Страница: 177 / 200

background image

Network controller stops working without apparent cause.

Cause

Solution

The files containing the network drivers are corrupted.

Reinstall the network drivers, using the Recovery Disc Set
created from the hard drive's Recovery Partition.

The cable is not securely connected.

Ensure that the cable is securely attached to the network
connector and that the other end of the cable is securely
attached to the correct device.

The network controller is defective.

Contact an authorized service provider.

New network card will not boot.

Cause

Solution

New network card may be defective or may not meet
industry-standard specifications.

Install a working, industry-standard NIC, or change the boot
sequence to boot from another source.

Cannot connect to network server when attempting Remote System Installation.

Cause

Solution

The network controller is not configured properly.

Verify Network Connectivity, that a DHCP Server is present,
and that the Remote System Installation Server contains the
NIC drivers for your NIC.

System setup utility reports unprogrammed EEPROM.

Cause

Solution

Unprogrammed EEPROM.

Contact an authorized service provider.

Solving Memory Problems

If you encounter memory problems, some common causes and solutions are listed in the following
table.

CAUTION:

Power may still be supplied to the DIMMs when the computer is turned off (depending

on the Management Engine (ME) settings). To avoid damage to the DIMMs or the system board, you
must unplug the computer power cord before attempting to reseat, install, or remove a DIMM module.

For those systems that support ECC memory, HP does not support mixing ECC and non-ECC
memory. Otherwise, the computer will not boot the operating system.

NOTE:

The memory count will be affected by configurations with the Management Engine (ME)

enabled. The ME uses 8MB of system memory in single channel mode or 16MB of memory in dual-
channel mode to download, decompress, and execute the ME firmware for Out-of-Band (OOB), third-
party data storage, and other management functions.

Solving Memory Problems 167

«
...
175
176
177
178
179
...
»

Содержание A7L26UT#ABA









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A7L26UT#ABA

Бренд: Raven Страницы: 18

Бренд: Raven Страницы: 232

Бренд: WAGO Страницы: 52

Бренд: Compaq Страницы: 2

Бренд: E-Medic Страницы: 31

BRIX GB-BACE-3150

Бренд: Gigabyte Страницы: 2

Бренд: Vivo Страницы: 5

Бренд: Dell Страницы: 3

Бренд: QNAP Страницы: 45

H6 i-One Series

Бренд: Cybernet Страницы: 30

Бренд: Shuttle Страницы: 35

Бренд: Shuttle Страницы: 1

Бренд: Shuttle Страницы: 64

Бренд: Shuttle Страницы: 27

Бренд: VarTech Systems Страницы: 8

Predator PO5-615s

Бренд: Acer Страницы: 42

CRT Touch Monitor

Бренд: 3M Страницы: 30

Бренд: IBM Страницы: 133

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды