HP A7L26UT#ABA Скачать руководство пользователя страница 180

Страница: 180 / 200

Table D-15

Solving CD-ROM and DVD Problems (continued)

System will not boot from CD-ROM or DVD drive.

Cause

Solution

Non-bootable CD in drive.

Try a bootable CD in the drive.

Boot order not correct.

Run the Computer Setup utility and change boot sequence in

Storage

Boot Order

Drive not found (identified).

Cause

Solution

Cable could be loose.

Check cable connections.

The system may not have automatically recognized a newly
installed device.

See reconfiguration directions in the

Solving Hardware

Installation Problems on page 163

section. If the system still

does not recognize the new device, check to see if the
device is listed within Computer Setup. If it is listed, the
probable cause is a driver problem. If it is not listed, the
probable cause is a hardware problem.

If this is a newly installed drive, run the Computer Setup
utility and try adding a POST delay under

Advanced

Power-On Options

The device is attached to a SATA port that has been hidden
in Computer Setup.

Run the Computer Setup utility and ensure

Device Available

is selected for the device's SATA port in

Security

Device

Security

Drive responds slowly immediately after power-up.

Run Computer Setup and increase the POST Delay in

Advanced

Power-On Options

CD-ROM or DVD devices are not detected or driver is not loaded.

Cause

Solution

Drive is not connected properly or not properly configured.

See the documentation that came with the optional device.

Movie will not play in the DVD drive.

Cause

Solution

Movie may be regionalized for a different country.

See the documentation that came with the DVD drive.

Decoder software is not installed.

Install decoder software.

Damaged media.

Replace media.

Movie rating locked out by parental lock.

Use DVD software to remove parental lock.

Media installed upside down.

Reinstall media.

170 Appendix D Troubleshooting Without Diagnostics

Содержание A7L26UT#ABA









































































































































































































Результаты поиска

Содержание A7L26UT#ABA

Отзывы:

Похожие инструкции для A7L26UT#ABA

Бренды по названию

Популярные бренды

HP A7L26UT#ABA, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание A7L26UT#ABA

Отзывы:

Похожие инструкции для A7L26UT#ABA

Бренды по названию

Популярные бренды