HP A7L26UT#ABA Скачать руководство пользователя страница 157

Страница: 157 / 200

Solving Diskette Problems

Common causes and solutions for diskette problems are listed in the following table.

NOTE:

The computer does not support internal diskette drives. Only USB diskette drives are

supported.

NOTE:

You may need to reconfigure the computer when you add or remove hardware, such as an

additional diskette drive. See

Solving Hardware Installation Problems on page 163

for instructions.

Table D-3

Solving Diskette Problems

Diskette drive light stays on.

Cause

Solution

Diskette is damaged.

Right-click

Start

, click

Explore

, and right-click on a drive.

Select

Properties

then select the

Tools

tab. Under

Error-

checking

click

Check Now

Diskette is incorrectly inserted.

Remove diskette and reinsert.

Drive cable is not properly connected.

Reconnect drive cable. Ensure that all four pins on the
diskette power cable are connected to the drive.

Drive not found.

Cause

Solution

Cable is loose.

Reseat diskette drive data and power cable.

Removable drive is not seated properly.

Reseat the drive.

The device has been hidden in Computer Setup.

Run the Computer Setup utility and ensure

Device Available

is selected for the Legacy Diskette in

Security

Device

Security

Diskette drive cannot write to a diskette.

Cause

Solution

Diskette is not formatted.

Format the diskette.

From Windows Explorer select the disk

(A)

drive.

Right-click the drive letter and select

Format

Select the desired options, and click

Start

to begin

formatting the diskette.

Diskette is write-protected.

Use another diskette or remove the write protection.

Writing to the wrong drive.

Check the drive letter in the path statement.

Not enough space is left on the diskette.

Use another diskette.

Delete unneeded files from diskette.

Diskette is damaged.

Replace the damaged disk.

Solving Diskette Problems 147

Содержание A7L26UT#ABA









































































































































































































Результаты поиска

Содержание A7L26UT#ABA

Отзывы:

Похожие инструкции для A7L26UT#ABA

Бренды по названию

Популярные бренды

HP A7L26UT#ABA, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание A7L26UT#ABA

Отзывы:

Похожие инструкции для A7L26UT#ABA

Бренды по названию

Популярные бренды