HP A7L26UT#ABA Скачать руководство пользователя страница 140

Страница: 140 / 200

Table C-1

Numeric Codes and Text Messages (continued)

Control panel message

Description

Recommended action

303-Keyboard Controller Error

I/O board keyboard controller.

Reconnect keyboard with computer
turned off.

Replace the system board.

304-Keyboard or System Unit Error

Keyboard failure.

Reconnect the keyboard with computer
turned off.

Ensure that none of the keys are
depressed.

Replace the keyboard.

Replace the system board.

501-Display Adapter Failure

Graphics display controller.

Reseat the graphics card
(if applicable).

Clear CMOS. (See Appendix B,

Password Security and Resetting
CMOS on page 177

Verify monitor is attached and turned
on.

Replace the graphics card (if possible).

510-Flash Screen Image Corrupted

Flash Screen image has errors.

Reflash the system ROM with the latest
BIOS image.

511-CPU, CPUA, or CPUB Fan not
Detected

CPU fan is not connected or may have
malfunctioned.

Reseat CPU fan.

Reseat fan cable.

Replace CPU fan.

512-Chassis, Rear Chassis, or Front
Chassis Fan not Detected

Chassis, rear chassis, or front chassis fan is
not connected or may have malfunctioned.

Reseat chassis, rear chassis, or front
chassis fan.

Reseat fan cable.

Replace chassis, rear chassis, or front
chassis fan.

513-Front Chassis fan not detected

Front chassis fan is not connected or may
have malfunctioned.

Reseat front chassis fan.

Reseat fan cable.

Replace front chassis fan.

514-CPU or Chassis Fan not Detected

CPU or chassis fan is not connected or may
have malfunctioned.

Reseat CPU or chassis fan.

Reseat fan cable.

Replace CPU or chassis fan.

515-Power Supply fan not detected

Power supply fan is not connected or may
have malfunctioned.

Reseat power supply fan.

Reseat fan cable.

Replace power supply fan.

130 Appendix C POST Error Messages

Содержание A7L26UT#ABA









































































































































































































Результаты поиска

Содержание A7L26UT#ABA

Отзывы:

Похожие инструкции для A7L26UT#ABA

Бренды по названию

Популярные бренды

HP A7L26UT#ABA, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание A7L26UT#ABA

Отзывы:

Похожие инструкции для A7L26UT#ABA

Бренды по названию

Популярные бренды