GigaDevice Semiconductor GD32E23 Series Скачать руководство пользователя страница 39

Страница: 39 / 547

GD32E23x User Manual

and LVDT[2:0] in the PWR_CTL register are read only.

SRAM_PARITY_

ERROR_LOCK

SRAM parity check error lock

This bit is set by software and cleared by a system reset.

0: The SRAM parity check error is disconnected from the break input of

TIMER0/14/15/16.

1: The SRAM parity check error is connected from the break input of

TIMER0/14/15/16.

LOCKUP_LOCK

Cortex-M23 LOCKUP output lock

This bit is set by software and cleared by a system reset.

0: The Cortex-M23 LOCKUP output is disconnected from the break input of

TIMER0/14/15/16.

1: The Cortex-M23 LOCKUP output is connected from the break input of

TIMER0/14/15/16.

1.5.7.

IRQ Latency register (SYSCFG_CPU_IRQ_LAT)

Address offset: 0x100

Reset value: 0x0000 0000

Reserved

IRQ_LATENCY

Bits

Fields

Descriptions

31:8

Reserved

Must be kept at reset value

7:0

IRQ_LATENCY

IRQ_LATENCY specifies the minimum number of cycles between an interrupt that

becomes pended in the NVIC, and the vector fetch for that interrupt being issued

on the AHB-Lite interface.

If IRQ_LATENCY is set to 0, interrupts are taken as quickly as possible.

For non-zero values, the Cortex-M23 processor ensures that a minimum of

IRQ_1 hclk cycles exist between an interrupt becoming pended in the

NVIC and the vector fetch for the interrupt being performed.

1.6.

Device electronic signature

The device electronic signature contains memory density information and the 96-bit unique

Содержание GD32E23 Series




































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GD32E23 Series

Отзывы:

Бренды по названию

Популярные бренды

GigaDevice Semiconductor GD32E23 Series, Руководство пользователя

Результаты поиска

Содержание GD32E23 Series

Отзывы:

Бренды по названию

Популярные бренды