manualshive.com logo in svg

GigaDevice Semiconductor GD32E23 Series, Руководство пользователя

Поделиться
Скачать
GigaDevice Semiconductor GD32E23 Series Скачать руководство пользователя страница 277

                                                                                                                     

GD32E23x User Manual

 

277 

 

 

Note:

 When CH3MS[1:0]=11, it is necessary to select an internal trigger input 

through TRGS bits in TIMERx_SMCFG register. 

7 

CH2COMCEN 

Channel 2 output compare clear enable. 

When  this  bit  is  set,  if  the  ETIFP  signal  is  detected  as  high  level,  the  O2CPRE 

signal will be cleared. 

0: Channel 2 output compare clear disable 

1: Channel 2 output compare clear enable 

6:4 

CH2COMCTL[2:0] 

Channel 2 compare output control   

This  bit-field  specifies  the  compare  output  mode  of  the  the  output  prepare signal 

O0CPRE.

 

In addition, the high level of O0CPRE is the active level, and CH0_O and 

CH0_ON channels polarity depends on CH0P and CH0NP bits. 

000:  Timing  mode.  The  O2CPRE  signal  keeps  stable,  independent  of  the 

comparison  between  the  output  compare  register  TIMERx_CH2CV  and  the 

counter TIMERx_CNT. 

001:  Set  the  channel  output.  O2CPRE  signal  is  forced  high  when  the  counter  is 

equals to the output compare register TIMERx_CH2CV. 

010: Clear the channel output. O2CPRE signal is forced low  when the counter  is 

equals to the output compare register TIMERx_CH2CV. 

011: Toggle on match. O2CPRE toggles when the counter  is equals to the output 

compare register TIMERx_CH2CV. 

100: Force low. O2CPRE is forced to low level. 

101: Force high. O2CPRE is forced to high level. 

110:  PWM  mode  0.  When  counting  up,  O2CPRE  is  high  when  the  counter  is 

smaller than TIMERx_CH2CV, and low otherwise. When counting down, O2CPRE 

is low when the counter is larger than TIMERx_CH2CV, and high otherwise. 

111: PWM mode 1. When counting up, O2CPRE is low when the counter is smaller 

than TIMERx_CH2CV, and high otherwise. When counting down, O2CPRE is high 

when the counter is larger than TIMERx_CH2CV, and low otherwise. 

If  configured  in  PWM  mode,  the  O2CPRE  level  changes  only  when  the  output 

compare mode is adjusted from 

“Timing” mode to “PWM” mode or the comparison 

result changes. 

This bit cannot be modified when PROT [1:0] bit-filed in TIMERx_CCHP register is 

11 and CH2MS bit-filed is 00(COMPARE MODE). 

3 

CH2COMSEN 

Channel 2 compare output shadow enable 

When  this  bit  is  set,  the  shadow  register  of  TIMERx_CH2CV  register,  which 

updates at each update event will be enabled.   

0: Channel 2 output compare shadow disable 

1: Channel 2 output compare shadow enable 

The PWM mode can be used without verifying the shadow register only in single 

pulse mode (when SPM=1) 

This bit cannot be modified when PROT [1:0] bit-filed in TIMERx_CCHP register is 

11 and CH0MS bit-filed is 00. 

Содержание GD32E23 Series




































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды