GigaDevice Semiconductor GD32E23 Series Скачать руководство пользователя страница 165

Страница: 165 / 547

GD32E23x User Manual

165

the ADC_CTL0 register. When the corresponding software trigger or external trigger is active,

the

ADC

samples

and

converts

the

channels

configured

the

ADC_RSQ0~ADC_RSQ2 registers until all the channels of routine sequence are done. The

EOC will be set after every circle of the routine sequence. An interrupt will be generated if the

EOCIE bit is set.

Figure 10-6. Discontinuous operation mode

CH2

CH1

CH5

CH7

CH11

CH16

CH2

CH1

· ·

EOC

One circle of routine sequence, RL=7, DISNUM=2

Sample

Convert

CH12

CH17

CH5

Routine

trigger

Software procedure for discontinuous operation mode on a routine sequence:

Set the DISRC bit in the ADC_CTL0 register and the DMA bit in the ADC_CTL1 register.

Configure the DISNUM [2:0] bits in the ADC_CTL0 register.

Configure the ADC_RSQx and ADC_SAMPTx registers.

Configure the ETERC and ETSRC bits in the ADC_CTL1 register if it is needed.

Prepare the DMA module to transfer data from the ADC_RDATA (refer to the spec of

the

DMA

module).

Set the SWRCST bit, or generate an external trigger for the routine sequence.

Repeat step6 if in need.

Wait the EOC flag to be set.

Clear the EOC flag by writing 0 to it.

10.4.6.

Conversion result threshold monitor function

The analog watchdog is enabled when the RWDEN bit in the ADC_CTL0 register is set for

routine sequence. This function is used to monitor whether the conversion result exceeds the

set thresholds, and the WDE bit in ADC_STAT register will be set. An interrupt will be

generated if the WDEIE bit is set. The ADC_WDHT and ADC_WDLT registers are used to

specify the high and low threshold. The comparison is done before the alignment, so the

threshold values are independent of the alignment, which is specified by the DAL bit in the

ADC_CTL1 register. One or more channels, which are selected by the RWDEN, WDSC and

WDCHSEL [4:0] bits in ADC_CTL0 register, can be monitored by the analog watchdog.

10.4.7.

Data storage mode

The alignment of data stored after conversion can be specified by DAL bit in the ADC_CTL1

When in the most significant bit alignment, the 12/10/8-bit data are aligned on a half-word,

while the 6-bit data are aligned on a byte basis as shown blew

Figure 10-7. Data storage

Содержание GD32E23 Series




































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GD32E23 Series

Отзывы:

Бренды по названию

Популярные бренды

GigaDevice Semiconductor GD32E23 Series, Руководство пользователя

Результаты поиска

Содержание GD32E23 Series

Отзывы:

Бренды по названию

Популярные бренды