ENSONIQ MR Rack, Руководство музыканта

Страница: 82 / 314

Chapter 4 —Parts
To access the Parameters described on this page (unless otherwise noted):
press the Params button, turn the Parameter knob to locate the parameter,
and then turn the Value knob to change the parameter's setting.
20 ENSONIQ MR-Rack Musician’s Manual
• I f the Pa r t r eceives a Cont r olle r 91 value o f 1-40, it will be assigned to the L ight R eve r b
bus.
• I f the Pa r t r eceives a Cont r olle r 91 value o f 41-80, it will be assigned to the
M edium R eve r b bus.
• I f the Pa r t r eceives a Cont r olle r 91 value o f 81-127, it will be assigned to the W et R eve r b
bus.
Tip:
See “ Using the I nse r t Cont r ol Pa r t to Pick I nse r t E ff ects V ia M I D I ” in Chapte r 5
to lea r n how to select I nse r t E ff ects via M I D I .
C ont r olling a P ar t ’ s P it c h Be nd R e spon se
A Pitch-Bend W heel is a sp r ing-loaded wheel typically located to the f a r le f t o f a M I D I
keyboa r d. I t ’ s most commonly used to bend the pitch o f notes up o r down by pushing the
wheel f o r wa r d ( up ) o r pulling it back ( down ) . Some manu f actu r e r s employ a le f t/ r ight
scheme.
T he M R - R ack o ff e r s two pa r amete r s — Pitch Bend Up and Pitch Bend Down — that allow you
to sepa r ately set how you want each Pa r t to r espond to M I D I Pitch Bend messages r eceived
f r om a Pitch Bend W heel pushed in eithe r di r ection.
T hese pa r amete r s will have no e ff ect i f the Pitch Bend R ecv pa r amete r is set to O ff . See “ T o
Enable o r Disable a Pa r t ’ s R eception o f Pitch Bend M essages ” late r in this chapte r .
The following parameter is not present when the Part being edited uses a Drum Kit.
To Set the Part’s Response To a Pitch Bend Wheel Pushed Forward
1. Use the Select Pa r t buttons to choose the Pa r t whose Pitch Bend you ’ d like to
customize.
2. P r ess the Pa r ams button.
3. T u r n the Pa r amete r knob until the display shows “ Pitch Bend Up=. ”
Pitch Bend Up can be set to :
• 1-12dn o r 1-12up — to lowe r o r r aise the pitch o f the Pa r t ’ s Sound by 1 to 12 equal-
tempe r semitones when a Pitch Bend W heel is pushed all the way f o r wa r d
• P r og — to r espond to upwa r d Pitch Bend movements acco r ding to the value
p r og r ammed into the Sound
• Sys — to use the global System Pitch Bend Up value ( see C h a p t er 3 f o r details )
• O ff— to igno r e M I D I messages r eceived f r om a Pitch Bend W heel pushed f o r wa r d
4. T u r n the V alue knob to select the Pitch Bend Up value you p r e f e r .
T his pa r amete r also r esponds to an R PN L SB value o f 000 and an N R PN L SB value o f 022.
See “ Using R PNs and N R PNs to Edit Pa r t Pa r amete r s ” at the end o f this chapte r .
The following parameter is not present when the Part being edited uses a Drum Kit.
To Set the Part’s Response To a Pitch Bend Wheel Pulled Back
1. Use the Select Pa r t buttons to choose the Pa r t whose Pitch Bend you ’ d like to
customize.
2. P r ess the Pa r ams button.
3. T u r n the Pa r amete r knob until the display shows “ Pitch Bend Down=. ”
Pitch Bend Down can be set to :