Dräger Savina 300 Скачать руководство пользователя страница 65

Страница: 65 / 166

Savina 300

309

000

_Pu

ati

Maintenance instructions

Replacing the consumables in the O2 gas inlet

Replacing the consumables in the O2 gas inlet

Introduction

The following section provides a view of the consumables in the O2 gas inlet
and describes how to remove and fit them.

View

The consumables are located in the O2 gas inlet (

Fig. 65

/1).

Fig. 65

Rear of device; fitting location of consumables

Removal

Preconditions

–

Savina 300 has been disconnected from the mains power supply and the
O2 supply.

–

ESD precautions have been taken.

–

The Savina 300 has been removed from the trolley, see „Disassem-
bling/assembling the device“ section headed „Removing/fitting the
Savina 300 from/into the trolley“.

–

The filter cover has been removed, see „Disassembling/assembling the
device“ section headed „Filter cover“.

–

The attached connectors and tubing have been disconnected from the
Savina 300.

–

The rear panel has been removed, see „Disassembling/assembling the
device“ section headed „Rear panel“.

Содержание Savina 300







































































































































































Результаты поиска

Содержание Savina 300

Отзывы:

Dräger Savina 300, Техническая документация инструкция, Страница: 65 / 166

Результаты поиска

Содержание Savina 300

Отзывы: