Dräger Savina 300 Скачать руководство пользователя страница 128

Страница: 128 / 166

.02

_00

253

ati

6DYLQD

Electrical safety

Electrical safety to EN 62353

18 / 50

6DYLQD

5HYLVLRQ

3.1.3

Protective earth conductor resistance measurement points

Action

• Scan the following measurement points for protective earth conductor

resistance measurement one after the other using the tip of the probe
cable:

– Power supply unit potential equalization pin

– Gas inlet O2

– Option, side-mounted rails

Result

Measurement points scanned

[________OK]

3.1.4

Device leakage current

Prerequisites

The tester is switched on.

Test set-up

Fig. 2

Device leakage current

Action

• Prepare the test setup.

• (applied part) Connect the device-specific test adapter on one end to the

device under test and on the other end to the tester's configurable socket
„A“ for applied parts (paying attention to the configuration!).

• Follow the instructions on the tester.

NOTE

– The device leakage current can be tested by the differential measure-

ment method or the direct measurement method.

– In direct measurement, set up the device under test with insulation and

scan all touchable conductive components using the probe (the protec-
tive conductor is internally interrupted in the tester).

Item Designation

Tester

Device under test

(applied part) Device-specific test adapter for tester

(applied part) Configurable sockets for applied parts

Conductor

Neutral conductor

Protective earth conductor

Содержание Savina 300







































































































































































Результаты поиска

Содержание Savina 300

Отзывы:

Dräger Savina 300, Техническая документация инструкция, Страница: 128 / 166

Результаты поиска

Содержание Savina 300

Отзывы: