Dräger Savina 300 Скачать руководство пользователя страница 148

Страница: 148 / 166

.02

_00

253

ati

6DYLQD

Function and condition test

Function tests

38 / 50

6DYLQD

5HYLVLRQ

4.2.6

Testing the ventilation

Prerequisites

The Savina 300 is connected to the mains power supply and to the „O2“ com-
pressed gas supply and switched on.

Action

• Prepare the following test setup:

Test set-up

Fig. 12

Test setup; testing the ventilation

Action

• Press the „Ventilation settings“ softkey and select „VC-CMV/VC-AC” mode.

• Set the following parameters:

– O2: 21%

– VT: 500 mL

– Ti : 2.0 s

– f: 12/min

– PEEP: 5 mbar

• Press the „Advanced settings“ softkey and set the following parameters:

– Sigh: Off

– Flow trigger: Off

– AutoFlow: Off

Item

Designation

Pressure gauge

Test lung

Y-piece, adult, Luer-Lock

Adult ventilation tubing

O2 analyzer

O2 adapter

Содержание Savina 300







































































































































































Результаты поиска

Содержание Savina 300

Отзывы:

Dräger Savina 300, Техническая документация инструкция, Страница: 148 / 166

Результаты поиска

Содержание Savina 300

Отзывы: