Dräger Savina 300 Скачать руководство пользователя страница 146

Страница: 146 / 166

.02

_00

253

ati

6DYLQD

Function and condition test

Function tests

36 / 50

6DYLQD

5HYLVLRQ

4.2.4

Power supply unit

Electrical supply display

Prerequisites

The Savina 300 is connected to the mains power supply.

Action

• Set the Savina 300 to „Standby“ mode.

Test

The LEDs on the front indicate the following operating states:

– „Mains power supply“ LED lit green; „External battery“ LED out

– „Internal battery“ LED lit „green“ when internal rechargeable batteries fully

charged or lit „yellow“ when the internal rechargeable batteries are charg-
ing.

Entry

[________OK]

Internal supply voltage (internal battery)

Prerequisites

Savina 300 is in „Standby“ mode.

Action

• Cut the mains power supply to the Savina 300.

Test

The acoustic alarm sounds. The message "Internal battery activated" is dis-
played on a yellow background. The LEDs on the front of the device indicate
the following operating states:

– „Mains power supply“ LED out; „External battery“ LED out

– „Interne battery“ LED lit „green“ or lit „yellow“

Action

• Press the „Start/Standby“ key and switch the Savina 300 to „VC-CMV/VC-

AC“ mode.

Entry

The blower runs up to speed. Ignore the error messages and alarms during
this test.

[________OK]

Action

• Connect the Savina 300 to the mains power supply.

Power failure alarm

Action

• Remove the fuse for the internal rechargeable battery. The fuse is located

on the rear panel of the unit.

Test

The message "

Internal

battery

is missing

" is displayed on a red background.

Action

• Press the „Alarm Reset“ key.

• Cut the mains power supply to the Savina 300.

Test

All LEDs on the front are out. The acoustic power failure warning sounds.

Action

• Switch off Savina 300.

Test

The acoustic alarm stops.

Action

• Re-insert the fuse for the internal rechargeable battery.

• Restore the mains power supply to the Savina 300.

• Switch on the Savina 300.

• Set the Savina 300 to „Standby“ mode.

NOTE

For the following tests do not connect any external battery or DC supply to
the Savina 300.

Содержание Savina 300







































































































































































Результаты поиска

Содержание Savina 300

Отзывы:

Dräger Savina 300, Техническая документация инструкция, Страница: 146 / 166

Результаты поиска

Содержание Savina 300

Отзывы: