Dräger Savina 300 Скачать руководство пользователя страница 55

Страница: 55 / 166

Savina 300

309

000

_Pu

ati

Maintenance instructions

Replacing the external batteries

Removal

Preconditions

–

The Savina 300 has been switched off and disconnected from the mains
power supply.

–

The connector of the DC battery cable has been disconnected from the
power supply unit of the Savina 300.

Procedure

1. Actuate all locking brakes on the double-wheel castors.

2. Remove the screw (

Fig. 51

/1), lift off the cover and place it aside.

Fig. 51

Detail view of trolley; screw

3. Remove the screws and split washers (

Fig. 52

/1) (2 of each) and discon-

nect the electrical cable with integrated tab fuse (25 A/32 V) (

Fig. 52

/3).

Fig. 52

View of external batteries; screws, split washers and electrical

cable

4. Remove the screws and split washers (

Fig. 52

/2) (2 of each).

The batteries are fixed in the battery pack by a strap. The central screw holds
the strap in place.

Содержание Savina 300







































































































































































Результаты поиска

Содержание Savina 300

Отзывы:

Dräger Savina 300, Техническая документация инструкция, Страница: 55 / 166

Результаты поиска

Содержание Savina 300

Отзывы: