Dräger Savina 300 Скачать руководство пользователя страница 18

Страница: 18 / 166

.13

_00

122

ati

Savina 300

Function descriptions

Control panel with TFT colour display

Control panel with TFT colour display

Control unit

The control panel is the interface between the unit and the user. The control
panel is used to enter and display the ventilation parameters.

Fig. 7

Block diagram of the control panel with TFT colour display

Membrane keypad

The keypad features the control keys and the associated LEDs.

TFT colour display

The 12.1” TFT colour display comprises the actual display and the backlight
converter. The TFT colour display has a resolution of 800 x 600 pixels.

The backlight converter generates a high voltage for the display backlighting.

Rotary encoder

The rotary knob is used to set and acknowledge the ventilation parameters.
The shaft encoder transmits square signals to the processor system as it
rotates, and the signals are then evaluated by the Central Control Board. The
voltage supply is +5 V.

Содержание Savina 300







































































































































































Результаты поиска

Содержание Savina 300

Отзывы:

Dräger Savina 300, Техническая документация инструкция, Страница: 18 / 166

Результаты поиска

Содержание Savina 300

Отзывы: