Dräger Savina 300 Скачать руководство пользователя страница 13

Страница: 13 / 166

Savina 300

309

000

_Pu

ati

Function descriptions

Electronic assembly

The fan cools the power pack.

Central Control Board

The Central Control Board is the device's central „control and monitoring
unit“. It has three separate processor systems (master processor, front pro-
cessor and display processor).

Three processor systems save the changeable, non-volatile data to
EEPROMs.

Fig. 2

Block diagram of the Central Control Board

Master processor

The master processor has the following tasks:

–

Activation of the actuators (valves, valve block, blower)

–

Reading of the measured values from the sensors

–

Control of the ventilation

–

Monitoring of the front processor

The master processor data are cached in the RAM.

The EEPROM of the master processor system stores the calibration data of
the sensors and set values such as volume.

Содержание Savina 300







































































































































































Результаты поиска

Содержание Savina 300

Отзывы:

Dräger Savina 300, Техническая документация инструкция, Страница: 13 / 166

Результаты поиска

Содержание Savina 300

Отзывы: