Dräger Savina 300 Скачать руководство пользователя страница 135

Страница: 135 / 166

6DYLQD

5HYLVLRQ

208

000

_Pu

ati

25 / 50

Electrical safety

Electrical safety according to IEC 60601-1

3.2.2

Protective conductor resistance

Test set-up

Fig. 5

Test setup for protective earth conductor resistance

Action

• Prepare the test setup.

• Switch on the tester and the device under test.

• Configure the tester appropriately, and follow the instructions on the tester.

• Using the tip of the test probe, scan the following points on the device

under test, move the power supply cord section-wise while doing so:

– Power supply unit earth pin

– Screws on the housing

– Oxygen connection

– Optional rails (on side of Savina)

– LPO option (connector)

Test

The protective conductor resistance must not exceed

0.2

Ohm (including

mains power cable) in each case.

Entry

Enter the highest measured value of the protective conductor resistance.

[________Ohm]

NOTE

The protective earth conductor resistance is measured with the power cable
connected.

Item Designation

Tester, e.g. SECUTEST

Device under test

Test probe with tip

Conductor

Neutral conductor

(Protective Earth) conductor

Содержание Savina 300







































































































































































Результаты поиска

Содержание Savina 300

Отзывы:

Dräger Savina 300, Техническая документация инструкция, Страница: 135 / 166

Результаты поиска

Содержание Savina 300

Отзывы: