Dräger Savina 300 Скачать руководство пользователя страница 117

Страница: 117 / 166

6DYLQD

5HYLVLRQ

208

000

_Pu

ati

7 / 50

Device configuration

Savina 300

Action

• Read off and note down the „Operating hours“ reading.

Entry

Operating hours

[________h]

Action

• Read off and note down the „Service hours“ reading.

Entry

Service hours

[________h]

1.1.4

Reading out customer-specific settings

Prerequisites

Savina 300 is connected to the mains power supply and is switched on.
Savina 300 is in „Standby“ mode.

Action

• Press the „Ventilation settings“ softkey.

• Select the „VC-CMV/VC-AC“ ventilation mode and read off and note down

the following parameters from the display:

Entry

[________txt]

Entry

[________txt]

Entry

[________txt]

Entry

[________txt]

Entry

FlowAcc

[________txt]

Entry

PEEP

[________txt]

Action

• Select the „Advanced settings“ submenu.

• Read and note down the following parameters from the display:

Entry

Sigh (ON or OFF)

[________txt]

Entry

Flow trigger (ON or OFF)

[________txt]

Entry

AutoFlow (ON or OFF)

[________txt]

Entry

int PEEP

[________txt]

Entry

Trigger

[________txt]

Action

• Press the „Alarms“ softkey.

• Read and note down the following parameters from the display:

NOTE

After completion of the test procedure, re-enter the customer-specific set-
tings before handing the unit over to the customer/owner.

Содержание Savina 300







































































































































































Результаты поиска

Содержание Savina 300

Отзывы:

Dräger Savina 300, Техническая документация инструкция, Страница: 117 / 166

Результаты поиска

Содержание Savina 300

Отзывы: