Dräger Savina 300 Скачать руководство пользователя страница 53

Страница: 53 / 166

Savina 300

309

000

_Pu

ati

Maintenance instructions

Replacing the internal batteries

Fitting

1. Place the new batteries in front of the Savina 300, paying attention to

their orientation (the lugs of the batteries point upwards towards the O2
supply).

2. Push the cable connectors (

Fig. 49

/1) firmly onto the lugs of the two bat-

teries, as shown in

Fig. 49

3. Push the cable connector (

Fig. 49

/2) (--) firmly onto the battery lug.

4. Insert the first battery in the battery compartment.

5. Push the cable connector (

Fig. 48

/1) (+) firmly onto the battery lug.

6. Insert the second battery in the battery compartment.

7. Use the screws (

Fig. 46

/1) to secure the cover plate (

Fig. 46

/2).

8. Fit the rear panel on the Savina 300, see section headed „Disassem-

bling/assembling the device“ section headed „Rear panel“.

9. Fit the filter cover on the Savina 300, see „Disassembling/assembling the

device“, section headed „Filter cover“.

10. Fit the Savina 300 on the trolley, see „Disassembling/assembling the

device“, section headed „Removing/fitting the Savina 300 from/into the
trolley“.

11. Insert the fuse link in the holder on the power supply unit.

12. Connect the Savina 300 to the mains power supply.

13. Perform the „electrical safety test“ and „function tests“ as per the test

instructions.

14. Leave the Savina 300 connected to the mains power supply until the

internal battery indicator lights up „green“.

Fitting of the batteries is now complete.

CAUTION

Batteries not fully charged! If the batteries are not fully charged, the running
time of the device in the event of a mains power failure may be reduced
considerably.

–

Inform the user that the rechargeable batteries still need to be
recharged.

Содержание Savina 300







































































































































































Результаты поиска

Содержание Savina 300

Отзывы:

Dräger Savina 300, Техническая документация инструкция, Страница: 53 / 166

Результаты поиска

Содержание Savina 300

Отзывы: