Dräger Savina 300 Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 166

Dräger Savina 300 Скачать руководство пользователя страница 131

6DYLQD

5HYLVLRQ

No

.0

208

_0

00

000

25

33

_Pu

bl

ic

ati

o

n

21 / 50

Electrical safety

Electrical safety to EN 62353

Test

The reference value must not exceed

5000

μA.

Result

Reference value

[________μA]

Test

The recurrent test value must not exceed

5000

μA.

Result

Recurrent test

[________μA]

3.1.7

Leakage current on applied part with test adapter (normal condition)

Prerequisites

The tester is switched on.

Test set-up

Fig. 4

Leakage current on applied part

NOTE

The test must be performed twice! The second test is performed with the
plug rotated 180° in the socket. In many test devices the mains plug rotation
is simulated by means of a built-in selector switch. The higher measured val-
ue must be documented.

NOTE

The reference value (initial measured value) must always be transmitted!

NOTE

If the measured values are between 90% and 100% of the permissible limit
value, the reference value and the previously measured values of the recur-
rent test should be applied to assess electrical safety!

NOTE

The following measurement is performed under „normal condition“.

Item Designation

1

Tester

2

Device under test

3

Applied part of device under test

4

Test adapter

5

Configurable sockets for applied parts

L

Conductor

N

Neutral conductor

PE

Protective earth conductor

«
...
129
130
131
132
133
...
»

Содержание Savina 300







































































































































































Отзывы:

Нет отзывов