Dräger Savina 300 Скачать руководство пользователя страница 133

Страница: 133 / 166

6DYLQD

5HYLVLRQ

208

000

_Pu

ati

23 / 50

Electrical safety

Electrical safety to EN 62353

3.1.8

Optional multiple socket strip on trolley

Power fuse links

Action

• Compare the power fuse links with rated values on the multiple socket

strip.

Test

The power fuse-links match the specifications on the multiple socket strip.

Result

[________OK]

Protective conductor resistance

Action

• Check the protective conductor contacts of all sockets on the multiple

socket strip with tester probe.

Test

The value of the protective earth conductor resistance must not exceed

0.3

ohms in each case.

Entry

Document the highest protective conductor resistance measurement in the
„Test Report“.

[________Ohm]

Equivalent device leakage current

Test

The initial value must not exceed

100

μA.

Entry

Initial value

[________μA]

Test

The recurrent test value must not exceed

100

μA.

Entry

Recurrent test

[________μA]

NOTE

The equivalent device leakage current test applies to the multiple-socket
outlet only!

NOTE

Always enter the initial value in a new „Test Report“ document.

Содержание Savina 300







































































































































































Результаты поиска

Содержание Savina 300

Отзывы:

Dräger Savina 300, Техническая документация инструкция, Страница: 133 / 166

Результаты поиска

Содержание Savina 300

Отзывы: