Daikin DCM601A51 Скачать руководство пользователя страница 153

Страница: 153 / 344

User’s Manual EM11A015B

intelligent Touch Manager

152

Thereafter, when the room temperature falls below the “se relative setup setpoint” by the

amount equivalent to the setback recovery temperature, the indoor unit is stopped. However to

avoid continual ON/OFF of the indoor unit, it is not stopped during the period of 30 minutes.

Setpoint

Time

During absence

During presence

During absence

Indoor unit is operated

in Cool mode at Cool setpoint.

Room

temperature

Room

temperature

Setup setpoint

Cool setpoint during
presence

Setback re
temperature (Cool) (1°C to 6°C range)

Indoor unit is turned

on to keep the setup setpoint.

When the target is operating in Heat, Auto(Heat), or Dependent (Heat) mode

While the room temperature is higher than “Setpoint – Relative Setback Setpoint”, the indoor

unit is stopped.

Room temperature is continuously monitored, and when it becomes lower than the “Setpoint –

Relative Setback Setpoint”, the indoor unit is started again.

Thereafter, when the room temperature exceeds the “Setpoint – Relative Setback Setpoint” by

the recovery temperature, the indoor unit is stopped. However to avoid continual ON/OFF of the

indoor unit, it is not stopped during the period of 30 minutes.

Setpoint

Setback setpoint

Heat setpoint during
presence

Setback recovery temperature (Heat)
(1°C to 6°C range)

Indoor unit is operated in Heat mode

at Heat setpoint.

Indoor unit is turned on to
keep the setup setpoint.

Time

During absence

During presence

During absence

Room

temperature

Room

temperature

When the target is operating in Fan or Dry mode

The indoor unit operates normally while people are present.

When no one is in, the indoor unit is put into Setback Inactive status and subsequent start/stop is

not performed.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды