Daikin DCM601A51 Скачать руководство пользователя страница 296

Страница: 296 / 344

User’s Manual EM11A015B

intelligent Touch Manager

295

<About air conditioner operation>

■

An air conditioner is not working.

• The air conditioner may be stopped by Interlocking Control. Check the Interlocking Control

settings.

Under the following conditions, the indoor units 1-01 will not work.

(1-00 and 1-01 are both started but thereafter, 1-01 is stopped by Interlocking Control.)

1-00 1-01 schedule starts indoor units 1-00 and 1-01.

When indoor unit 1-00 is ON, 1-01 is stopped by Interlocking Control.

Outdoor
unit

1-00

1-01

Indoor unit 1-01 stopped
when 1-00 is started
by interlocking control

Main
unit

Indoor units 1-00 and 1-01
started by schedule

In the case above, Interlocking Control stops 1-01 though it was started by Schedule.

⇒

looks as if it is not working.

When setting up a schedule or interlocking control, carefully consider interaction with other

schedule programs and interlocking programs.

■

Other equipment stops when an indoor unit and the like are started from iTM. (Unexpected

behavior)

•

Check interlocking control settings.

Interlocking Control function may be set to stop other equipment when an indoor unit is put

into operation.

Check the settings as indicated below.

Check interlocking control settings using the Setup Export function.

For details of the Setup Export function, see “7-3 Outputting Function Settings”.

Check control state of the relevant equipment in the history.

For details of History function, see “7-1 Checking and Outputting History”.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды