Daikin DCM601A51 Скачать руководство пользователя страница 186

Страница: 186 / 344

User’s Manual EM11A015B

intelligent Touch Manager

185

•

Action Setup Screen

This screen is displayed when you touch the Action Setup button on the Interlock Program

Output Setup screen.

Sets the actions that will be performed by an output event of the interlocking program.

This screen consists of six tabs: Common, R/C Prohibition, A/C, Ventilator, Ao. Mo, and HW

Supply, each outputting different event actions. The screen opens on the tab that corresponds to

the type of the selected management point/area.

Setting items of functions not available for the management point being registered do not

display.

NOTE

•

Common Tab (Action Setup Screen)

This screen is displayed when you touch the Common tab on the Action Setup screen.

Sets up actions for common items.

(1)

(2)
(3)

(4)

(5)

(6)

(1)

On/Off

Select the On/Off check box to start/stop the target.

In the case of the system with Hydrobox, the button

(2)

(3)

and

(4)

are able to control the air

conditioners only, but they are unable to control the water heater.

(2)

Start

radio button

Select to start the target.

(3)

Stop

radio button

Select to stop the target.

(4)

Setback High

Setback Low

radio buttons

Select either of the two radio buttons when using the Setback function.

These radio buttons are displayed only when the optional Setback function is enabled.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды