Daikin DCM601A51 Скачать руководство пользователя страница 199

Страница: 199 / 344

User’s Manual EM11A015B

intelligent Touch Manager

198

Display the Registration screen and register the group members.

(6)

(7)

(6)

is the list of registered management points registered with the group while

(7)

is the list of

management points that can be registered.

To add a management point, select one from

(7)

and touch the Add button. To remove a

management point, select one from

(6)

and touch the Remove button.

The management points you can register are limited to indoor units. You can register up to 512

indoor units in one group. You cannot register the same indoor unit in multiple groups.

When finished, touch the OK button to return to the Temperature Limit screen.

• For indoor units without the Changeover option, make sure an indoor unit that uses the

same refrigerant and has Changeover option is registered in the same group.

• Indoor units to be subject to the same control can be registered in the same group even if

they are not located in the same space.

NOTE

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Похожие инструкции для DCM601A51

Бренды по названию

Популярные бренды