Daikin DCM601A51 Скачать руководство пользователя страница 54

Страница: 54 / 344

User’s Manual EM11A015B

intelligent Touch Manager

4-3 Standard View (List) Screen

(8)

(1)

(19)

(7)

(9)

(10) (11)

(12)

(13)

(14)

(15)

(16)

(17)

(18)

(2)

(3)

(4)

(5)

(6)

(1)

Area/Management Point

view

Displays information on the areas and management points of the hierarchical level displayed in the

area hierarchy indicator.

(2)

Menu List

switch button

Switches to the Menu List screen, which consists of Automatic Ctrl., System Settings, Operation

Mgmt. and Energy Navigator (optional) tabs.

(3)

Standard View

switch button

Switches from the Layout View screen (optional) to the Standard View screen.

(4)

Layout View

switch button

Switches the screen to the Layout View screen (optional), which displays indoor units in a floor plan.

Displayed only when the Layout View option is enabled.

NOTE

(5)

Lock/Unlock

button

Locks/Unlocks the switching of the screen from the Menu List screen. The button is grayed out

when the screen lock is disabled.

(6)

Time

Displays the current time.

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды