Daikin DCM601A51 Скачать руководство пользователя страница 291

Страница: 291 / 344

User’s Manual EM11A015B

intelligent Touch Manager

290

14.

Troubleshooting

14-1 Before Having the Product Serviced

<About iTM unit>

■

The display of the iTM has gone out.

• Check the MONITOR button LED on the unit.

If it is lit in orange, the monitor is turned off. Press the MONITOR button and turn the monitor

on. The LED lights on in green.

• When Backlight Auto Off is set in the screensaver settings of the iTM, the screen goes off if left

untouched for a certain period of time.

Touch the screen with your finger. The display will come back on.

■

The backlight does not go out although Backlight Auto is set to OFF.

• Backlight Auto Off is a function that automatically turns the display OFF when the screen is left

untouched for a certain period of time.

The display does not go out automatically when it is displaying “Configure/Details”, “System

Settings”, etc.

■

The iTM cannot be operated or monitoring does not work.

• Move the sliding front cover and press the RESET button at the bottom right of the iTM.

Pressing this switch restarts the iTM.

(Pressing this switch does not erase area/management point settings, schedules, etc.)

• When using the Power Proportional Distribution function, no pulse input is accepted while iTM

is being restarted.

MONITOR

CPU ALIVE

SLAVE

MASTER

BACKUP

LAN SW

SERVICE LAN

FRONT BACK

MASTER

OFF

RESET

LAN LINK D

MONITOR

RESET

Useful Information

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды