Daikin DCM601A51 Скачать руководство пользователя страница 58

Страница: 58 / 344

User’s Manual EM11A015B

intelligent Touch Manager

(8)

Icon (Area, Management Point)

Displays area and management point icons.

(9)

Info

Displays auxiliary information of the area or management point.

(10)

View panel

Displays the entire background image.

(11)

Scope

Indicates the portion of the background image that is displayed as background on the screen. To

move, touch the scope and drag.

(12)

Layout selection

list

The title selected in this list is the displayed layout.

(13)

Back

button

Displays the previous screen again.

(14)

Information

button

Displays the legend for an icon or contact information for inquiries regarding the system.

(15)

Operation Window bar

Touching the bar displays the Operation Window. To close, touch the bar again.

The operating procedure of the Operation Window is the same as that of the Standard View screen.

See the descriptions for the Standard View screen (“4-2 Standard View (Icon)Screen ” and “4-3

Standard View (List) Screen”).

Содержание DCM601A51

























































































































































































































































































































































Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды

Daikin DCM601A51, Руководство пользователя

Результаты поиска

Содержание DCM601A51

Отзывы:

Бренды по названию

Популярные бренды